Coleman 9955 - Manual (Page 12)

English - 11
Problem: Grill will not light when the igniter
button is pushed or has incomplete burner
flame.
Possible Causes and Solutions:
1. Lack of fuel. Check to see that the cylinder has fuel.
2. Make sure the burner is turned on. Allow up to four
seconds for gas flow to ignite.
3. If burner lights with match but not igniter, check
the ceramic electrode position near the burner, the
condition of the igniter wire and its connections.
Perform igniter test and replace any damaged parts.
4. Check for spider webs or insect nest in venturi and
clean venturi.
5. Check for misalignment of venturi on orifices. Position
venturi over orifices.
6. Burner ports, orifices or knob have blockage. Clean the
components.
7. Regulator failure; regulator needs to be replaced by an
authorized service dealer.
8. Make sure the regulator and cylinder are properly
assembled. See the section titled “Installing 1 lb.
Propane Cylinders”.
Problem: Yellow flame.
Possible Causes and Solutions:
1. Check for spider webs or insect nest in the venturi and
clean the venturi.
2. New burner may have residual oil which will burn off.
3. Clean off any food residue, grease or seasoning salts on
the burner.
4. The venturi may be misaligned and needs to be lined up
over the orifice.
Problem: Flame blows out on low setting or
has uneven heat distribution.
Possible Causes and Solutions:
1. Check for spider webs or insect nests in the venturi and
clean the venturi.
2. Cold grill needs to be preheated for 5 minutes on high
setting.
3. The venturi may be misaligned and needs to be lined up
over the orifices.
4. Cold and windy weather will require you to move the
grill away from the wind.
5. Lack of fuel. Check to see that the cylinder has fuel.
Problem: Grill too hot.
Possible Causes and Solutions:
1. Excessive flareups which require the maintenance
described in the section titled
“IN CASE OF GREASE FIRE”.
2. A damaged orifice or regulator which requires
replacement with factory authorized parts.
3. Buildup of grease inside the grill will require cleaning
and emptying the grease tray.
4. Choose a lower cooking temperature if using
excessively high settings.
Problem: Fire at any connection.
Possible Causes and Solutions:
IMMEDIATELY shut off control knob and allow grill
to cool.
1. Gas is leaking from a faulty connection. Tighten
connections with an adjustable wrench and replace
damaged parts. Perform a leak test on all connections
before cooking on the grill again.
Problem: Flame behind control panel or control
knob area.
Possible Causes and Solutions:
IMMEDIATELY shut off control knob and allow grill
to cool.
1. Check for spider webs or insect nest in the venturi and
clean the venturi.
2. Gas is leaking from a faulty connection. Hand tighten
connections and replace damaged parts. Perform a leak
test on all connections before cooking on the grill again.
3. The venturi may be misaligned and needs to be lined up
over the orifices.
Moving the grill:
r
DO NOT move the grill while it is lit or hot, or with objects
on the cooking surface.
r
Clean the grease tray before moving the grill to
prevent spills.
r
Collapse the grill before moving.
r
Move the grill slowly. DO NOT run with the grill behind
you; it could hit you from behind causing injury.
After moving the grill:
r
Check all gas connections for leaks that could occur from
the movement.
r
Check the venturi tubes to be sure they are still over
the orifices .
Steps to follow before storing grill:
r
Clean the grill, including the grease tray.
r
Coat the burner lightly with cooking oil to retard rusting.
r
For outdoor use only. If the grill is stored indoors, detach
the cylinder outdoors. If left outdoors, remove the cylinder
and cover the grill for protection from the weather. Grill
covers may be purchased from a grill dealer
or manufacturer.
Moving and Storage
Troubleshooting
A collision with the grill, as with any metal object, could
cause injury. Use care when moving a portable gas grill.
CAUTION