Dell PowerVault 122T LTO (Autoloader) - Manual (Page 20)

Error Codes
Back to Contents Page
must be preceded by the '3' and '0' characters to be considered valid.
Error
Code Description Details
3 0 81 Invalid Command Error. This error indicates that the autoloader received an undefined command or an invalid parameter with a command.
3 0 82 Device Status Not Suitable to
Execute This Command.
If the robotics are busy, some commands cannot be executed at the same time. This error indicates a probable
violation. This is not an error condition, but does result in Busy being reported to the host for the requested SCSI
command.
3 0 83 Inventory Not Valid. The cartridge inventory is not valid because of manual changes or previous fatal errors. Update the inventory using
the Re-inventory option in the Configuration menu. See "
Creating an Inventory of Cartridges " or power cycle the
autoloader.
3 0 84 Source Empty. There is no cartridge in the location from which a cartridge move was issued.
3 0 85 Destination Full. The location to which a cartridge move was issued already contains a cartridge.
3 0 86 Import/Export Slot Access
Rejected.
User attempted to access the Import/Export slot, but media removal was prevented by the host.
3 0 87 Operation Timeout. A command did not complete in the required amount of time.
3 0 88 Communications Error During
Loop-Back.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 89 System Test Timeout. There was a communication timeout between the drive and loader during the System Test.
3 0 8F Recovered Loader Error. Loader error recovery successful. Your diagnostic tool can provide details of the original loader error.
3 0 90 Mechanical Initialization Failure. The robotics were not able to move to the safe mechanical initialization position. Manual intervention is necessary.
3 0 91 Inventory Scan Failure. Fatal robotic error occurred during the inventory scan.
3 0 92 Preposition Failed. Belt positioning error occurred during Preposition command.
3 0 93 Cartridge Load Error. A failure occurred while trying to load a cartridge a slot to the drive.
3 0 94 Cartridge Unload Error. A failure occurred while trying to unload a cartridge from the drive to its slot.
3 0 95 Import Error. An error occurred while trying to import a data cartridge to a carousel slot.
3 0 96 Export Error. An error occurred while trying to export a data cartridge from its carousel slot. Can be caused by an empty slot that
is expected to be full.
3 0 A0 Carousel Motion Failure. Error occurred during carousel movement (Position Not Found). Could be caused by a missing or misaligned cartridge
carrier, or an obstruction, or unexpected cartridge in either the carousel path or Import/Export slot.
3 0 A1 Cartridge Transport Position
Error.
Cartridge transport element is unable to reach its desired position. Failure occurred while trying to place a cartridge
into or remove a cartridge from the drive or a slot.
3 0 A2 Gripper Position Error. Gripper unable to reach position.
3 0 A3 Cartridge Pick Error. Error occurred while trying to pull a cartridge from the drive or a carousel slot.
3 0 A4 Import/Export Slot Position
Error.
The Import/Export slot door was not in the requested position during device operation. Can be caused by manually
opening the door, or a cartridge or other obstruction is blocking the door. Try removing the cartridge or obstruction,
then power cycle or reset the autoloader.
3 0 A5 Fan Error. Autoloader processor detected a fan error.
3 0 B0 ROM Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B1 RAM Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B2 NVRAM Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B3 Controller Timer Failure. An unrecoverable failure has occurred in the controller timer circuit.
3 0 B4 Loader To Drive Communication
IC Error.
Failure in IC handling loader to drive communication.
3 0 B5 Display Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B6 Memory Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B7 Timeout on Autoloader
Command
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BA Drive Load Timeout. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BB Drive Unload Timeout. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BC Overtemperature problem. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BD No connection to drive. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BE Generic drive response error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BF Fatal Error. Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.