Dell PowerEdge 2650 - Manual (Page 12)

E07FA TEMP CPU n
THERM
Specified microprocessor is out of
acceptable temperature range and is
operating at a reduced speed, or
frequency. Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "
System Fans "). If the problem persists, ensure that the
microprocessor heat sinks are properly installed. If the problem persists, replace the
faulty microprocessor (see "
Microprocessors ").
E0876 POWER PS n No power available from the specified
power supply; specified power supply is
improperly installed or faulty. Ensure that the power supplies are properly installed. If the problem persists, replace
the faulty power supply(s) (see "
Power Supplies ").
E0880 INSUFFICIENT
PS
Insufficient power is being supplied to the
system; power supplies are improperly
installed, faulty, or missing.
E0CB2 MEM SPARE
BANK
Correctable errors threshold was met in a
memory bank: errors were remapped to
the spare bank. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0CF1 MBE DIMM
Bank n
Memory modules installed in the specified
bank are not the same type and size;
faulty memory module(s). Ensure that all banks contain memory modules of the same type and size and that
they are properly installed. If the problem persists, replace the faulty memory module
(s) (see "
Memory Modules ").
E0CF1 POST MEM 64K Parity failure in the first 64 KB of main
memory. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0CF1 POST NO
MEMORY
Main-memory refresh verification failure. Ensure that all banks contain memory modules of the same type and size and that
they are properly installed. If the problem persists, replace the faulty memory module
(s) (see "
Memory Modules ").
E0CF5 LOG DISABLE
SBE
Multiple single-bit errors on a single
memory module. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0D76 DRIVE FAIL Faulty or improperly installed hard drive or
RAID controller. Ensure that the hard drives are properly installed. If the problem persists, replace the
faulty hard drive(s) (see "
Hard Drives "). If the problem persists, replace the RAID
controller (see " Integrated RAID Controller " and " RAID Controller Card ").
E0F04 POST CMOS CMOS write/read failure; faulty system
board. Replace the system board (see " System Board ").
E0F04 POST CPU
SPEED
Microprocessor speed control sequence
failure. Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "
Microprocessors ").
E0F04 POST DMA
INIT
DMA initialization failure; DMA page
register write/read failure. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0F04 POST DMA REG Faulty system board. Replace the system board (see " System Board ").
E0F04 POST KYB
CNTRL
Faulty keyboard controller; faulty system
board. Replace the system board (see " System Board ").
E0F04 POST MEM
RFSH
Main-memory refresh verification failure. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0F04 POST PIC REG Master or slave PIC register test failure. Replace the system board (see " System Board ").
E0F04 POST SHADOW BIOS-shadowing failure. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules ").
E0F04 POST SHD
TEST
Shutdown test failure.
E0F04 POST SIO Super I/O chip failure; faulty system
board. Replace the system board (see " System Board ").
E0F04 POST TIMER Programmable interval timer test failure;
faulty system board. Replace the system board (see " System Board ").
E0F0B POST ROM
CHKSUM
Faulty or improperly installed expansion
card. Ensure that the expansion cards are properly installed. If the problem persists,
replace the faulty expansion card(s) (see "
Expansion Cards ").
E0F0C VID MATCH
CPU n
Specified microprocessor is faulty,
unsupported, improperly installed, or
missing. Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "
Microprocessors ").
E10F3 LOG DISABLE
BIOS
BIOS disabled logging errors. Check the SEL for details on the errors.
E13F2 IO CHANNEL
CHECK
Faulty or improperly installed expansion
card; faulty system board. Ensure that the expansion cards are properly installed. If the problem persists,
replace the faulty expansion card(s) (see "
Expansion Cards "). If the problem persists,
replace the system board (see " System Board ").
E13F4 PCI PARITY
E13F5 PCI SYSTEM
E13F8 CPU BUS INIT Faulty or improperly installed
microprocessor or system board. Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "
Microprocessors "). If the problem persists,
replace the system board (see " System Board ").
E13F8 CPU BUS
PARITY
Faulty system board. Replace the system board (see " System Board ").
E13F8 CPU MCKERR Machine check error; faulty or improperly
installed microprocessor; faulty system
board. Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "
Microprocessors "). If the problem persists,
replace the system board (see " System Board ").
E13F8 HOST BUS Faulty system board. Replace the system board (see " System Board ").
E13F8 HOST TO PCI
BUS
E13F8 MEM
CONTROLLER
Faulty or improperly installed memory
module; faulty system board. Ensure that the memory modules are properly installed. If the problem persists,
replace the faulty memory module(s) (see "
Memory Modules "). If the problem
persists, replace the system board (see " System Board ").
E1580 POWER
CONTROL
Faulty system board. Replace the system board (see " System Board ").
E20F1 OS HANG Operating system watchdog timer timed
out. Restart your system. If the problem persists, see your operating system
documentation.