Dell PowerEdge 1750 - Manual (Page 10)

Invalid memory configuration detected.
Potential for data corruption exists!
Memory modules are not installed in
matched pairs. Install memory modules in matched pairs. See " Memory ."
Invalid NVRAM configuration, resource re-
allocated
System configuration data has been
ignored. Check the System Setup configuration settings. See
"
Using the System Setup Program ."
I/O card parity interrupt at address Expansion card(s) is improperly installed
or faulty. Reinstall the expansion card(s). See " Expansion Cards ." If
the problem persists, replace the expansion card(s).
Keyboard controller failure Defective keyboard/mouse controller
(defective system board). Replace the system board. See " System Board ."
Keyboard data line failure
Keyboard stuck key failure
Keyboard clock line failure
Keyboard failure
Keyboard cable connector is loose or
improperly connected; defective
keyboard; defective keyboard/mouse
controller (defective system board). Check the keyboard cable connection. Replace the
keyboard. If the problem persists, replace the system
board. See "
System Board ."
Memory allocation error Memory module(s) is not connected
properly, or an application program or the
operating system failed. Reseat the modules. See " Memory ." Reboot the system. If
the message reappears, see your software
documentation.
Memory address line failure at address, read
value expecting value
Memory high data line failure at start address
to end address
Memory high address line failure at start
address to end address
Memory double word logic failure at start
address to end address
Memory double word logic failure at address,
read value expecting value
Memory odd/even logic failure at start address
to end address
Memory odd/even logic failure at address, read
value expecting value
Memory write/read failure at address, read
value expecting value
Memory write/read failure at start address to
end address
Faulty or improperly seated memory
modules or defective system board. Remove and reseat the memory modules. See " Memory ."
If the problem persists, replace the memory modules. If
the problem persists, replace the system board. See
"
System Board ."
Memory parity failure at start address to end
address
Memory parity error at address
Improperly seated or faulty memory
modules. Remove and reseat the memory modules. See " Memory ."
If the problem persists, replace the memory modules.
No boot device available Faulty diskette, diskette/CD drive
subsystem, hard drive, or hard-drive
subsystem; no boot disk in drive A. Replace the diskette. Replace the diskette drive or the
hard drive. See "
Installing a Diskette Drive " or " Internal
SCSI Hard Drives ." If the problem persists, replace the
system board. See " System Board ."
No boot sector on hard- disk No operating system on the hard drive. Check the hard-drive configuration settings in the System
Setup program. See "
Using the System Setup Program ."
No timer tick interrupt Defective system board. Replace the system board. See " System Board ."
No PXE-capable device available <F12> was pressed during POST and no
PXE devices are detected. Check the cables connected to the NICs. Check the
configuration settings in the System Setup program for
the NICs. See "
Using the System Setup Program ."
Non-system disk or disk error Faulty diskette, diskette drive subsystem,
or hard-drive subsystem. Replace the diskette. Reseat all drives and reboot the
system. If the error message reappears, replace the
system board. See "
System Board ."
Not a boot diskette No operating system on diskette. Use a bootable diskette.
PCI BIOS failed to install PCI device (option ROM) checksum failure
is detected during shadowing. Contact the PCI device manufacturer to obtain a suitable
replacement PCI option ROM. Follow the manufacturer's
instructions to install the option ROM.
Plug & Play Configuration Error Error encountered when initializing the
PCI device, or the system board is
defective. Install the NVRAM_CLR jumper and reboot the system.
See
Figure 5 -2 for jumper location. If the problem
persists, replace the system board. See " System Board ."
Plug & Play Configuration Error PCI_n Error encountered when initializing the
PCI adapter. Install the NVRAM_CLR jumper and reboot the system.
See
Figure 5 -2 for jumper location. If the problem
persists, replace the specified expansion card. See
"
Expansion Cards ." If the problem persists, replace the
system board. See " System Board ."
Primary backplane error Improperly attached or missing
backplane. Ensure that the SCSI backplane board is fully seated. See
"
SCSI Backplane Board ."
Primary IDE device 0 not found
Primary IDE device 1 not found
Improperly connected or missing IDE
device. Ensure that the device's interface cable is securely
connected to the SCSI backplane board. See "
Installing a
Diskette Drive " or " Installing a CD Drive ." If the problem
persists, replace the device.