Dell PowerEdge 1750 - Manual (Page 11)

Processor 1 internal error
Processor 2 internal error
Defective microprocessor or system board
(reported by the NMI handler). Replace the specified microprocessor. See
"
Microprocessors ." If the problem persists, replace the
system board. See " System Board ."
Processor 1 is a 533-MHz system bus processor
Processor 2 is a 533-MHz system bus processor
Two 533-MHz microprocessors are
installed. This system supports only
Intel® Xeon™ 400-MHz front-side-bus
processors. Reboot the system. If you receive beep code 4-4-3
(processor frequency mismatch), replace both processors
with Intel Xeon 400-MHz front-side-bus processors. See
"
Microprocessors ."
If a beep code does not occur at system boot, turn off the
system, install the NVRAM_CLR jumper, and reboot the
system. See
Figure 5 -2 for jumper location.
Processor bus error
PCI bus error
IMB bus error
Defective system board (reported by the
NMI handler). Replace the system board. See " System Board ."
Processor x is not a 533-MHz system bus
processor
This system bus speed is not supported on this
system board
This system supports only Intel Xeon 533-
MHz front-side bus (system bus)
processors. Reboot the system. If you receive beep code 4-4-3
(processor frequency mismatch), replace processor x with
a supported processor. See "
Microprocessors ."
If a beep code does not occur at system boot, turn off the
system, install the NVRAM_CLR jumper, and reboot the
system. See
Figure 5 -2 for jumper location.
Read fault
Requested sector not found
Faulty diskette, diskette-drive subsystem,
or hard-drive subsystem. Replace the diskette. Reseat all drives and reboot the
system. If the message reappears, replace the diskette
drive. See "
Installing a Diskette Drive ." If the problem
persists, replace the system board. See " System Board ."
Reset failed Improperly connected diskette/tape drive,
hard drive, or power cable. Check the drive and cable connections, and reset the
system again.
ROM bad checksum = address Expansion card improperly installed or
faulty. Reinstall the expansion card. See " Expansion Cards ." If
the problem persists, replace the expansion card.
Sector not found
Seek error
Seek operation failed
Defective sectors on diskette or hard
drive.
Faulty diskette, diskette-drive subsystem,
or hard-drive subsystem.
Replace the diskette, or reseat all drives and reboot the
system. See "
Installing a Diskette Drive " or " Internal SCSI
Hard Drives ." If the message reappears, replace the drive
(s). If the problem persists, replace the system board.
See "
System Board ."
Shutdown failure Defective system board. Replace the system board. See " System Board ."
System backplane error Improperly attached or missing SCSI
backplane. Reseat the SCSI backplane. See " SCSI Backplane Board ."
System halted! Must power down. Wrong password entered too many
times. Reboot the system and enter the correct password. If the
problem persists, see "
Disabling a Forgotten Password ."
System parity error Defective expansion card(s) or improperly
seated or faulty memory modules
(reported by the NMI handler). Replace the expansion cards one at a time until the error
is corrected. See "
Expansion Cards ."
Remove and reseat the memory modules. See " Memory ."
If the problem persists, replace the memory modules. If
the problem persists, replace the system board. See
"
System Board ."
The following memory DIMMs are unsupported:
DIMM_xx.
This system only supports 266 MHz DIMMs.
One or more of the installed DIMMs has a
frequency less than 266 MHz. System
memory must be rated for 266 MHz. Replace lower-speed DIMM(s) with modules rated for 266-
MHz operation. See "
Memory ."
This processor system bus speed is unknown.
System halted!
The installed microprocessor is not
supported by the system. Reboot the system. If you receive beep code 4-4-3
(processor frequency mismatch), replace the installed
microprocessor(s) with microprocessor(s) supported by
your system. See "
Microprocessors ."
If a beep code does not occur at system boot, turn off the
system, install the NVRAM_CLR jumper, and reboot the
system. See
Figure 5 -2 for jumper location.
This system only supports 400-MHz system bus
speed.
System halted!
Two 533-MHz microprocessors are
installed. This system supports only Intel
Xeon 400-MHz front-side-bus processors. Reboot the system. If you receive beep code 4-4-3
(processor frequency mismatch), replace both processors
with Intel Xeon 400-MHz front-side-bus processors. See
"
Microprocessors ."
If a beep code does not occur at system boot, turn off the
system, install the NVRAM_CLR jumper, and reboot the
system. See
Figure 5 -2 for jumper location.
Time-of-day clock stopped Defective battery or faulty chip (defective
system board). Replace the system battery. See " System Battery ." If the
problem persists, replace the system board. See " System
Board ."
Time-of-day not set - please run SETUP program Incorrect Time or Date settings or
defective system battery. Check the Time and Date settings. See " Using the
System Setup Program ." If the problem persists, replace
the system battery. See " System Battery ." If the problem
persists, replace the system board. See " System Board ."
Timer chip counter 2 failed Defective system board. Replace the system board. See " System Board ."
Unsupported CPU combination Microprocessor combination is not
supported by the system. Install a supported microprocessor combination. See
"
Microprocessors ."
Unsupported CPU stepping detected. Microprocessor is not supported by the
system. Install the correct version of the microprocessor in the
specified microprocessor socket. See "
Microprocessors ."
Utility partition not available <F10> key was pressed during POST, but Create a utility partition on the boot hard drive. See