Dell Precision M60 User Manual

Page 62

Advertising
background image

POST —

power-on self-test — Diagnostics programs, loaded automatically by the BIOS, that perform basic tests on the major computer components, such as

memory, hard drives, and video. If no problems are detected during POST, the computer continues the start-up.  

program —

Any software that processes data for you, including spreadsheet, word processor, database, and game packages. Programs require an operating

system to run.  

PS/2 —

personal system/2 — A type of connector for attaching a PS/2-compatible keyboard, mouse, or keypad.  

PXE —

pre-boot execution environment — A WfM (Wired for Management) standard that allows networked computers that do not have an operating system to

be configured and started remotely.

R

 

RAID —

redundant array of independent disks — A system of two or more drives working together for performance and fault tolerance. RAID drives are

typically used on servers and high-end PCs. The three most common RAID levels are 0, 3, and 5:

l

 

Level 0: Provides data striping but no redundancy. Level 0 improves performance but does not provide fault tolerance.

l

 

Level 3: Same as Level 0, but also reserves one dedicated drive for error correction data, providing good performance and some level of fault

tolerance.

l

 

Level 5: Provides data striping at the byte level and also stripe error correction information, resulting in excellent performance and good fault

tolerance.

 

RAM —

random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut

down your computer.  

readme file —

A text file included with a software package or hardware product. Typically, readme files provide installation information and describe new

product enhancements or corrections that have not yet been documented.  

read-Only —

Data and/or files you can view but cannot edit or delete. A file can have read-only status if:

l

 

It resides on a physically write-protected floppy disk, CD, or DVD.

l

 

It is located on a network in a directory and the system administrator has assigned rights only to specific individuals.

 

refresh rate —

The frequency, measured in Hz, at which your screen's horizontal lines are recharged (sometimes also referred to as its vertical frequency). The

higher the refresh rate, the less video flicker can be seen by the human eye.  

resolution —

The sharpness and clarity of an image produced by a printer or displayed on a monitor. The higher the resolution, the sharper the image.  

RFI —

radio frequency interference — Interference that is generated at typical radio frequencies, in the range of 10 kHz to 100,000 MHz. Radio frequencies are

at the lower end of the electromagnetic frequency spectrum and are more likely to have interference than the higher frequency radiations, such as infrared
and light.  

ROM —

read-only memory — Memory that stores data and programs that cannot be deleted or written to by the computer. ROM, unlike RAM, retains its

contents after you shut down your computer. Some programs essential to the operation of your computer reside in ROM.  

RPM —

revolutions per minute — The number of rotations that occur per minute. Hard drive speed is often measured in rpm.  

RTC —

real time clock — Battery-powered clock on the system board that keeps the date and time after you shut down the computer.  

RTCRST —

real-time clock reset — A jumper on the system board of some computers that can often be used for troubleshooting problems.

S

 

ScanDisk —

A Microsoft utility that checks files, folders, and the hard disk's surface for errors. ScanDisk often runs when you restart the computer after it has

stopped responding.  

SDRAM —

synchronous dynamic random-access memory — A type of DRAM that is synchronized with the optimal clock speed of the microprocessor.  

serial connector —

An I/O port often used to connect devices such as a handheld digital device or digital camera to your computer.  

service tag —

A bar code label on your computer that identifies your computer when you access Dell Support at support.dell.com or when you call Dell for

customer service or technical support.  

setup program —

A program that is used to install and configure hardware and software. The setup.exe or install.exe program comes with most Windows

software packages. Setup program differs from system setup program.  

shortcut —

An icon that provides quick access to frequently used programs, files, folders, and drives. When you place a shortcut on your Windows desktop

and double-click the icon, you can open its corresponding folder or file without having to find it first. Shortcut icons do not change the location of files. If you
delete a shortcut, the original file is not affected. Also, you can rename a shortcut icon.  

shutdown —

The process of closing windows and exiting programs, exiting the operating system, and turning off your computer. You can lose data if you turn

off your computer before completing a shutdown.  

smart card —

A card that is embedded with a microprocessor and a memory chip. Smart cards can be used to authenticate a user on computers equipped for

smart cards.  

software —

Anything that can be stored electronically, such as computer files or programs.  

Advertising