Sony CPD-100SF - Manual (Page 8)

Entering New Timings Use of the Tilt-Swivel
When using a video mode that is not one of the factory
preset modes, some fine tuning may be required to optimize
the display to your preferences. Simply adjust the monitor
according to the preceding adjustment instructions. The
adjustments will be stored automatically and recalled
whenever that mode is used.
A total of 10 user-defined modes can be stored in memory.
If the 11th mode is entered, it will replace the first.
Power Saving Function
This monitor meets the power saving guidelines set by the
Tntemational ENERGY STAR Program as well as the more
stringent NUTEK 803299 (TC092) guidelines. It is capable
of reduced power consumption when used with a computer
equipped with Display Power Management Signaling
(DPMS). By sensing the absence of the sync signal coming
from the computer, it will reduce the power consumption as
follows:
CAUTION: The Power Saving function will automatically
put the monitor into Active-off state if the power
switch is turned on without any video signal
input. Once the horizontal and vertical syncs are
sensed, the monitor will automatically return to
its Normal operation state.
State
Power
consumption
Required
resumption
time
(!)
POWER
indicator
POWER
SAVING
indicator
1
Normal
operation
100% — green on off
2
Suspend
(1st step of
power saving)
approx.
10%
approx.
3 sec.
green on orange on
3
Active-off
(2nd step of
power saving)
approx. 7%
approx.
10 sec.
off orange on
4 Power-off approx. 7% - off off
If you want the power consumption to be OW, unplug the
power cord.
Plug and Play
This monitor complies with the DDC™1, DDC2B and
DE)C2AB which are the Display Data Channel (DDC)
standards of VESA.
When a DDCl host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification Data) to the data line.
When a DDC2B or DDC2AB host system is connected, the
monitor automatically switches to each commimication.
DDC™ is a trademark of Video Electronics Standard
Association.
8
With the tilt-swivel, this unit can be adjusted to be viewed at
your desired angle within 90° horizontally and 20° vertically.
To turn the unit vertically and horizontally, hold it at its
bottom with both hands.
Damper Wire
Using a white background, very thin horizontal stripe on
the screen is visible as shown on the illustraHon. This stripe
is damper wire. This wire is attached to the aperture grille
inside the Trinitron tube and is there to damp vibrations of
the aperture grille in order to prevent them from
influencing to the picture quality.
!
Damper wire
Approx. 6 cm
Specifications
Picture tube
Viewable image size
Logical resolution
Physical resolution
0.25 mm aperture grille pitch
15 inches measured diagonally
90-degree deflection
Approx. 284
X 212 mm (w/h)
(111/4 X 8 3/8 inches)
13.9" viewing image
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Horizontal: Max. 1024 dots
Vertical: Max. 768 lines
Standard image area Approx. 270 x 202 mm (w/h)
(10 3/4x8 inches)
Deflection frequency Horizontal: 30 to 70 kHz
Vertical: 50 to 120 Hz
AC input voltage/current
100 to 120 V, 50/60 Hz, 1.8 A
220 to 240 V, 50 - 60 Hz, 1 A
Dimensions Approx. 368 x 373 x 384.5 mm (w/h/d)
(141/2 X 14 3/4 X 15 1/4 inches)
Mass Approx. 14 kg (30 lb 14 oz)
Design and specifications are subject to change without
notice.