Craftsman 1/2HP Garage Door Opener 139.53515SR - Manual (Page 19)

Radio Controls
RC.C. rules prohibit adjustments to or modification of receiver and transmitter circuitry except for changini
code setting and replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PAr
Manufactured under 1 or more of the loHowing U.S. patents; RE29.S2S; 4.037.201; 4,750,118; 4308,930. Other patents pen<Sng.
the
>bur 53000SR SERIES garage door opener (with RECEIVER ‘SR’ CODE BUTTON) has been factory set to operate
with the LARGE push button on the transmitter. The 3-function transmitter(s) can also activate additional garage
door openers and/or light controls • 53000 and/or 53000SR SERIES.
Instructions are given below for matching the code in all transmitters, changing your code selection or using the
transmitterfs) with other receivers.
MATCH/CHANGE THE CODE IN TRANSMITTER(S)
SET CODE SWITCHES IN ALL TRANSMITTERS TO MATCHING POSITIONS
1. Locate the code switches in transmitter(s), either by sliding battery compartment cover down or by removing cover
screw and carefully turning case top over.
2. With a pen or a screwdriver, change the setting of one or more switch (to a (+), (-) or (0) position).
NOTE: Code switches 2 through 9 in ALL transmitters used to operate a receiver must be set to match. (Code
switch 1 on a 3-function transmitter is neutral. Set it to ANY position. It will not affect the code selected).
Standard
' 3-Functioo
Transmitter
-Code Switcftes
(1-9)
CO c CO-
.
Standard
3-Function
Transmitter
“Code Switches
(2-9)
CJIID
3-Function
■ Mini Transmitter
- Code Switches
(1-9)
SET RECEIVER TO MATCH TRANSMITTER(S) CODE
53000SR SERIES (WITH RECEIVER CODE BUTTON)
Garage Door Openers and Light Controls
(Illustration A shows a garage door opener receiver)
3 FUNCTION
TRANSMITTER
Select a transmitter push
button to operate receiver
GARAGE DOOR
OPENER RECEIVER
(With SR Code Button)
WHT BLK VEL
Indicator
Code Button Light
3, Press the RECEIVER SR code button on the right side
panel of opener (Illustration A). The indicator light will
turn ON.
4. STAND AWAY FROM THE DOOR and press the
selected push button on the transmitter. The indicator
light will turn OFF emd door will move. Receiver and
transmitter codes now match and the opener will
operate with the selected push buton on the treinsmitter.
NOTE: If transmitter push button is not pressed
within 30 seconds, the indicator light will turn OFF.
Begin again at Step 3.
TO USE THE TRANSMITTER(S) WITH OTHER 53000SR
SERIES RECEIVERS: Select another transmitter push
button to operate the Light Control or additional garage
door opener. Make sure all transmitters used to operate
receiver are set to the same code (Steps 1 and 2). Repeat
Steps 3 and 4.
53000 SERIES (WITH RECEIVER CODE SWITCHES)
Garage Door Openers and Light Controls
(Illustration B shows a garage door opener receiver)
Push Button (•)
Push Button (-f)
3 FUNCTION
TRANSMITTER
Select a transmitter
push button to operate
receiver
Push Button (0)
RED WHT BLK
О (S
■•I
GARAGE DOOR
OPENER RECEIVER
(With Code Switches)
Slide receiver oode
switch #1 to position
that matches selected
transmitter push button
(-r, 0 or -)
With code switch #1
set in the (-) position,
receiver will operate
with transmitters'
large push button
3 Locate the receiver code switches. Get code switch #l
to match transmitter push button you want to use with
that receiver (■!■), (0) or (-). Refer to illustration (B).
4. Hold a transmitter (with code switches visible) along­
side the receiver. Beginning with RECEIVER code
switch #2, match the position of each transmitter
switch.
TO USE THE TRANSMITTER(S) WITH OTHER 53000
SERIES RECEIVERS: Select another transmitter push
button to operate the Light Control or additional garage
door opener. Make sure all transmitters are set to a match­
ing code (Steps 1 and 2). Repeat Steps 3 and 4.
19