Kontron AM5010 User Manual
User guide, Am5010
Advertising
Table of contents
Document Outline
- Revision History
- Imprint
- Disclaimer
- Table of Contents
- List of Tables
- 1-1 System Relevant Information 1 - 5
- 1-2 AM5010 Main Specifications 1 - 10
- 1-3 Standards 1 - 15
- 1-4 Related Publications 1 - 16
- 2-1 Module Management LED Function 2 - 7
- 2-3 POST Code Sequence 2 - 8
- 2-2 User-Specific LED Function 2 - 8
- 2-5 DIP Switch SW2 Functions 2 - 9
- 2-6 DIP Switch SW3 Functions 2 - 9
- 2-7 DIP Switch SW5 Functions 2 - 9
- 2-4 POST Code Example 2 - 9
- 2-8 Module Handle Positions 2 - 10
- 2-9 USB Connectors J3/J5 Pinout 2 - 11
- 2-10 USB NAND Flash Con. J9 Pinout 2 - 11
- 2-11 Serial Connector J7 (COM1) Pinout 2 - 12
- 2-12 Gigabit Ethernet Connectors J4 / J6 Pinout Based on Implementation 2 - 13
- 2-13 DVI-I Connector J2 Pinout 2 - 14
- 2-14 SATA Port Routing 2 - 15
- 2-15 SATA Extension Connector J8 Pinout 2 - 15
- 2-16 Pinout of AMC Card-edge Connector J1 2 - 19
- 2-17 Reserved Pins Description 2 - 22
- 2-18 Extended Options Region Pins Description 2 - 22
- 2-19 JTAG Pins Description 2 - 22
- 2-20 Processor and Chipset Supervision 2 - 24
- 2-21 AMC-Specific Signals 2 - 24
- 2-22 Onboard Power Supply Supervision 2 - 24
- 2-23 Temperature Signals 2 - 25
- 4-1 SW2 Functions 4 - 3
- 4-2 User-Specific LED Configuration (BIOS POST Code) 4 - 4
- 4-3 BIOS Firmware Hub Flash Configuration 4 - 4
- 4-4 BIOS Boot Order Configuration 4 - 4
- 4-5 BIOS CMOS Configuration 4 - 4
- 4-6 Configuration of DIP Switch SW3, Switches 1 and 2 4 - 5
- 4-7 Configuration of DIP Switch SW5, Switches 1 and 2 4 - 5
- 4-8 Interrupt Setting 4 - 6
- 4-9 I/O Address Map 4 - 7
- 4-10 BIOS Configuration Register 4 - 8
- 4-11 MMC I/O Status Register 4 - 9
- 4-12 Watchdog Timer Control Register 4 - 11
- 4-13 AMC Geographic Addressing Register 4 - 12
- 4-14 Board and Logic Revision Register 4 - 12
- 4-15 Reset Status Register 4 - 13
- 4-16 Host I/O Status Register 4 - 14
- 4-17 Host I/O Configuration Register 4 - 14
- 4-18 Board ID Register 4 - 14
- 4-19 Board Interrupt Configuration Register 4 - 15
- 4-20 Hot Swap Status Register 4 - 15
- 4-21 User-Specific LED Configuration Register 4 - 16
- 4-22 User-Specific LED Control Register 4 - 18
- 4-23 Serial Over LAN Configuration Register 4 - 19
- 4-24 Delay Timer Control / Status Register 4 - 20
- 4-25 MMC Configuration Register 4 - 21
- 5-1 DC Operational Input Voltage Ranges 5 - 3
- 5-2 Payload Power Consumption: AM5010 with Core™2 Duo, 1.5 GHz 5 - 5
- 5-3 IPMI FRU Payload Power Consumption of the AM5010 5 - 5
- 5-4 Payload Start-Up Current of the AM5010 5 - 6
- 6-1 Pressure Drop vs. Airflow Data 6 - 10
- 6-2 Deviation of the Airflow Rate on the AM5010 6 - 11
- A-1 SATA Adapter Main Specifications A - 3
- A-2 Board-to-Board Connector J1 Pinout A - 6
- A-3 SATA Connector J2 Pinout A - 7
- List of Figures
- 1-1 AM5010 Functional Block Diagram 1 - 6
- 1-2 AM5010 Front Panel 1 - 7
- 1-3 AM5010 Board Layout (Top View) 1 - 8
- 1-4 AM5010 Board Layout (Bottom View) 1 - 9
- 2-1 Front Panel LEDs 2 - 6
- 2-2 Module Handle Positions 2 - 10
- 2-3 USB Connectors J3/J5 2 - 11
- 2-4 USB NAND Flash Connector J9 2 - 11
- 2-5 Serial Connector J7 (COM1) 2 - 12
- 2-6 Gigabit Ethernet Connectors J4/J6 2 - 13
- 2-7 DVI-I Connector J2 2 - 14
- 2-8 SATA Extension Connector J8 2 - 15
- 2-9 AM5010 Port Mapping 2 - 17
- 3-1 Module Handle Positions 3 - 4
- 4-1 DIP Switch SW2 4 - 3
- 6-1 Board Temperature Sensor Placement (AM5010 Bottom View) 6 - 4
- 6-2 Processor Temperature Sensor Placement (AM5010 Top View) 6 - 5
- 6-3 Temperature vs. Airspeed Graph of the AM5010 6 - 9
- 6-4 AM5010 Impedance Curve 6 - 10
- 6-5 Thermal Zones of the AM5010 Module 6 - 11
- A-1 SATA Adapter Functional Block Diagram A - 4
- A-2 SATA Adapter Layout A - 5
- A-3 SATA Connector J2 A - 7
- Proprietary Note
- Trademarks
- Environmental Protection Statement
- Explanation of Symbols
- For Your Safety
- Two Year Warranty
- 1. Introduction