La-Z-Boy AirSpa Massage System - Manual (Page 5)

8. Choose a location for the chair that is close to an electr ical outlet and
proceed to the Operating Instr uctions .
9. To remove the back, unplug the Power Transfor mer and rever se the Assembly
Instructions steps .
9 8
6. Connect the Power Transfor mer.
• Locate the Power Transfor mer secured to the base rail. Carefully cut the
ca ble tie and remove the Power Transfor mer from the rail. Remove the
packing and unwind the cord.
• Align the Power Transfor mer connector with the connector located next to
the rear body rail, and push the connector s tightly together (F IGURE 5, on
previous page). Keep the cord to the back of the chair, away from the
bottom of the base and mechanism.
7. Retur n the chair to its upr ight position.
• Hold the Power Transfor mer cord away from the base and retur n the chair
to the upr ight position. Make sure the Power Transfor mer cord is not
pinched between the base and the floor. Return the seat and back to the
upright position.
AirSpa ® 10-Motor Massage & Heat Recliner
Assembly Instr uctions:
– To reduce the risk of serious injur y:
• Check the condition of the power transfor mer s , electr ical cords , plugs
and connector s monthly. Keep the power transfor mer and electr ical
cords away from heat sources. Never operate the unit with a damaged
power transfor mer, electr ical cord, plug or connector. Contact your
La-Z-Boy ® dealer for ser vice.
– To reduce the risk of serious injur y:
• Provide a clear path for operation of the back and legrest. Place
ta bles and area r ugs at a distance to allow the legrest to fully extend
without r ubbing or interference.
NOTICE:
To prevent damage to the connectors and cords, it is
impor tant to unfasten all connections prior to removing the back.
Plug the Power Transfor mer into a wall outlet.
AirSpa ® 10-Motor Massage and Heat Functions and Automatic Timers
The AirSpa ® system contains two over la pping lumbar pillows w hich inflate and
deflate to provide a rolling massage, with an automatic timer that will shut off
the massage after 30 minutes of operation. The 10-Motor Vibrating Massage
system can be set for 15 or 30 minutes of operation. The Heat function will shut
off automatically after 30 minutes of operation.
• Press the PWR button, at the top left on the hand wand, once to star t the
15 minute vibrating massage; or press and hold down the PWR button to
start the 30 minute vibrating massage. To restart, press the PWR or ZONE button.
• Press the ZONE button to select from the five vibrating massage zones .
Any or all of the zones can be selected.
• Press the HEAT button once to select low heat and twice to select high heat.
• Press the PULSE, WAVE or CIRCLE button to select a vibrating massage mode.
Each mode has three actions .
• Press the PWR button, at the bottom left on the hand wand, to star t the
AirSpa ® massage. The lumbar suppor t pillows will inflate for three seconds
ever y time the AirSpa ® system is tur ned on.
• Press the INFLATE or DEFLATE button to customize the lumbar suppor t.
• Press the LOWER BACK button and select HIGH, MED, or LOW to customize
the lower back massage. Reclining in the chair will provide a firmer massage.
(Operating Instructions Continued)
AirSpa ® 10-Motor Massage & Heat Recliner
Operating Instr uctions:
– To reduce the risk of serious injur y:
• Sit down in the unit slowly. To avoid tip over, do not throw your weight
against the back of the unit. Move the unit into or out of the reclining
position slowly, making sure that no children or pets are in close proximity.
• To safely exit the unit and prevent a tripping hazard bring the back
upright and close the legrest.
NOTICE:
The massage functions may star t automatically
when electrical power is restored after a power outage. The timers
should automatically shut down the chair within 30 minutes. There
should be no risk of injur y or damage if this happens.
WARNING
WARNING
– To reduce the risk of serious injur y:
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
WARNING
DANGER