Tjernlund SB1 Hot Shot Stove Blower 8504181 - Manual (Page 2)

Install the Directional Chute on the end of the Heat Capture Chute if desired. The Directional Chute allows airflow to be directed left or right
up to 45 degrees or straight to extend the length of the Heat Capture Chute. If using the Directional Chute follow steps below. If not using
the Directional Chute proceed to Step 4.
1. Align the Directional Chute with the Heat Capture Chute. Insert the provided threaded stud into the holes located in both arms of the
Directional Chute and through the slots in the Heat Capture Chute, (See Figure A).
2. Loosely install the provided washer and acorn nut on each threaded stud, (See Figure B). Slide the Directional Chute into the Heat
Capture Chute to the end of the slots being careful not the scratch the paint and lightly hand tighten the acorn nuts.
3A. STRAIGHT DISCHARGE: For a straight discharge, simply tighten the (2) acorn nuts and proceed to Step 4.
3B. ANGLED DISCHARGE: For an angled discharge, adjust to desired angle before tightening (2) acorn nuts. NOTE: The inside
corner of the Directional Chute should bend at the pivot point at the end of the Heat Capture Chute, (See Figure C). Adjust and
tighten the acorn nut on pivot side first and then adjust to the desired angle and tighten acorn nut opposite pivot side, (See Figure D).
4. Using the 3 clips on the blower housing, clip the SB1 to the stove’s heat shield, (See Figure E). The SB1 is designed so that once
clipped to a standard heat shield the discharge will rest on the stove top. If the stove’s heat shield is too high or curved cut an opening
that is 5/8” lower than stove top and just wide enough for the SB1 Heat Capture Chute to fit through. If the heat shield is too low, add a
piece of sheet metal to it that is 5/8” lower than the stove top and wide enough for the (3) SB1 mounting clips. IMPORTANT: To pro-
tect the fan motor from excessive heat, the SB1 must be mounted with the motor housing outside the heat shield of the stove, (See
Figure F). If the stove does not have a heat shield purchase Tjernlund part 950-9200 Heat Shield Kit .
5. Plug the unit in, making sure the cord of the unit is routed to avoid contact with any heat sources. On/Off switch is located in rear
bottom near cord exit.
ATIOREPLACEMENT PARTS / ACCESSORIES
OPERATION
N
The SB1 operates by a manual switch located in the rear bottom of unit. For best results, turn the blower on before fire is started. Run
the blower continuously while heat is being produced by the stove. Let the blower continue to run 30 minutes after the fire has extin-
guished. The blower must operate the entire time heat is being produced by the stove. Operating the blower in this manor is the most
efficient way to keep the spaces it serves comfortable while insuring the blower components are not over exposed to excessive heat.
ACCESSORIES & WARRANTY
Component Part Number
Heat Shield Kit 950-9200
TJERNLUND LIMITED ONE YEAR WARRANTY
Tjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from defects due to faulty material or workmanship for a period of (1) year from the date of original
purchase or delivery to the original purchaser, whichever is earlier. Remedies under this warranty are limited to repairing or replacing, at our option, any product which shall, within the above stated war-
ranty period, be returned to Tjernlund Products, Inc. at the address listed below, postage prepaid. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF, AND TJERNLUND PRODUCTS, INC. EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF THIS PRODUCT. THIS
WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND NO AGENT IS AUTHORIZED TO ASSUME FOR US ANY LIABILITY ADDITIONAL TO THOSE SET FORTH IN THIS LIMITED
WARRANTY. IMPLIED WARRANTIES ARE LIMITED TO THE STATED DURATION OF THIS LIMITED WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so that
limitation may not apply to you. In addition, some states do not allow the exclusion or limitation of incidental or consequential damages, so that above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which may vary from State to State. Send all inquiries regarding warranty work to Tjernlund Products, Inc. 1601 9th Street,
White Bear Lake, MN 55110-6794. Phone (651) 426-2993 • (800) 255-4208 • Fax (651) 426-9547 • Email [email protected].
FIGURE A FIGURE B FIGURE C
FIGURE D FIGURE E FIGURE F
STOVE HEAT
SHIELD
SB1 MOUNT
CLIP (3)
OPPOSITE
PIVOT SIDE
SLOT
PIVOT
POINT
PIVOT
SIDE
STUD
WASHER &
ACORN NUT
PIVOT
SIDE