Vintage Cellars Howard Miller Niagara - Manual

SAFETY TIPS
• Ensure that the cabinet is positioned square and firm on the floor so that it will not fall over.
Some cabinets are equipped with adjustable floor levelers. Adjust the levelers for
maximum stability and proper alignment (Figure 1).
• Some cabinets include a Safety Strap. Follow the instructions included with the Safety
Strap to ensure maximum stability (See step #3 in Cabinet Set Up Instructions).
• Some cabinets are illuminated. Combustible materials or those adversely affected by
drying or fading from the heat should not be placed close to the lamp.
• Some cabinets include a cabinet door lock. Lock the cabinet door to keep the contents
secure and away from minors.
• Some cabinets include a location for a cooler. Follow the cooler manufacturer’s installation
instructions for clearance and caution issues.
• Keep plastic bags and small parts away from children.
CABINET SET UP INSTRUCTIONS:
1. Turn the adjustable floor levelers, located on the bottom of the cabinet, all the way in
(up) (Figure 1).
2. Inspect the inside of the cabinet, carton and packaging to make sure you have removed
all separately packed parts. Do NOT dispose of any packing material until the set up is
complete.
If your cabinet has shelves, they may be secured inside the cabinet with shipping clips.
To remove the shipping clips, you will need a Phillips screwdriver (Figure 2). The shelves
may also be packed on top, underneath, or along side of the cabinet. You may need to
lay the cabinet on it’s backside to remove the shelves from underneath the cabinet. Use
caution when removing these shelves.
3. Move the cabinet to its final location.
Locate any electrical cords that may be exiting the back or bottom of the cabinet. Move
them out of the way as you move the cabinet to its final location.
Some cabinets include a Safety Strap to prevent tipping. If a Safety Strap was included
with your cabinet, review the instructions included with the Safety Strap at this time and
choose the assembly option which best fits your application. The cabinet should be
attached to the wall for maximum stability. If your cabinet does not have this feature,
proceed to the next step.
4. Install the Shelves, Racks, and other separately packed parts.
Do NOT put any items onto the shelves or racks until completely finished with the set up
instructions.
The shelves may not all be the same size. Please use care to install each shelf in it’s
proper location within the cabinet. The shelves will rest on Shelf Clips or wood rails
inside the cabinet.
Pad-Lock ™ Shelf Clips: Securely place the Shelf Clips into the desired holes inside the
cabinet (Figures 3 and 4). There may be several holes that can be used for shelf height
adjustment. Position the shelves onto the Shelf Clips as shown in Figures 3 and 4.
5. Close and secure the door(s) using the lock or latch provided with your cabinet.
6. Level the Cabinet. Place a level alongside the cabinet from front-to-back and side-to-side
(Figure 5). There are adjustable levelers under the cabinet (Figure 1) that can be turned
in (up) or out (down) to make adjustments. Adjust the levelers until the cabinet is level
in all directions, and is square and firm on the floor.
INSTRUCTIONS FOR WINE & SPIRITS CABINET
FIGURE 2
FIGURA 2
FIGURE 2
ABBILDUNG 2
FIGURE 3
FIGURA 3
FIGURE 3
ABBILDUNG 3
FIGURE 5
FIGURA 5
FIGURE 5
ABBILDUNG 5
FIGURE 1
FIGURA 1
FIGURE 1
ABBILDUNG 1
FIGURE 4
FIGURA 4
FIGURE 4
ABBILDUNG 4
CAUTIONS FOR USE OF GLASS SHELVES:
To prevent breakage of glass shelves and/or items placed on the glass shelves, good judgement must be used
during the installation and loading of glass shelves.
Sudden shock from any size item can result in broken glass, personal injury, or damage to valuable items. Care
should be taken when placing items onto each glass shelf.
The weight of items placed on the shelves must be evenly distributed and must not exceed 25 pounds.
The end use of this cabinet is beyond our control and therefore, the Howard Miller Company can not assume
responsibility for broken shelves or personal effects.
Pad-Lock™ Shelf Clip
Pad-Lock TM Soporte de repisa
Cornière Pad-Lock™
Pad-Lock TM Regalklemme
Shipping Clip
Ajuste del sujetador
Attache de transport
Transportklemme
Distribute Load Evenly on Shelf.
Do NOT exceed 25 pounds.
Distribuya el peso sobre la repisa por igual.
NO exceda de 25 libras (11.35 Kg.)
Répartir la charge de façon uniforme sur l’étagère.
NE PAS dépasser 11,35 kg (25 lb).
Last gleichmäßig auf dem Regal verteilen.
Darf 11 kg NICHT überschreiten.
FIGURE 6
FIGURA 6
FIGURE 6
ABBILDUNG 6
Leveler
Nivelador
Patin de réglage
Nivellierfuß
CORRECT
CORRECTO
CORRECT
RICHTIG
INCORRECT
INCORRECTO
INCORRECT
FALSCH