Nexen 5H70PSP 914000 - Manual (Page 6)

6 FORM NO. L-20060-U-1209
TaBle 3
FIGure 1
Clutch
Coupling, Sprocket,
Gear, or Pulley
Customer
supplied
Key
Optional
Hub Collar
Shaft
Set Screw
(Item 20)
r o F
l e d o M
r a ll o C
. D . O
E R O B
t c u d o r P
. o N
d e p p a T
s e l o H
d e ri u q e r
. C . B
N I M M
P S P 0 3 H 5 8 / 5 - 1 5 7 8 . 3 2 . 2 2 0 0 3 4 2 9 2 3 - 6 ) 3 ( 6 1 / 3 - 1
P S P 5 3 H 5 6 1 / 5 1 - 1 5 2 1 . 1 8 5 . 8 2 0 0 4 4 2 9 2 3 - 6 ) 3 ( 6 1 / 7 - 1
P S P 0 4 H 5 6 1 / 5 1 - 1 0 5 2 . 1 5 7 . 1 3 0 0 5 4 2 9 0 4 - 4 ) 4 ( 2 / 1 - 1
P S P 5 4 H 5 8 / 5 - 2 0 0 5 . 1 0 1 . 8 3 0 0 6 4 2 9 2 3 - 8 ) 3 (
- 3 / 9 2 - 1
2
P S P 0 5 H 5 4 / 3 - 2 0 5 7 . 1 5 4 . 4 4 0 0 7 4 2 9 2 3 - 8 ) 3 ( 2 3 / 5 - 2
P S P 0 6 H 5 8 / 1 - 3 7 3 9 . 1 0 2 . 9 4 0 0 8 4 2 9 2 3 - 0 1 ) 3 ( 6 1 / 7 - 2
P S P 0 7 H 5 2 / 1 - 3 7 8 1 . 2 5 5 . 5 5 0 0 9 4 2 9 2 3 - 0 1 ) 3 (
- 1 / 1 1 - 2
6
P S P 0 8 H 5 4 7 3 9 . 2 0 6 . 4 7 0 0 0 5 2 9 4 2 - 0 1 ) 3 (
- 6 / 9 1 - 3
4
Mounting positions of the Tooth Clutch may be vertical
or horizontal. In the vertical position Nexen recommends
locating the drive flange in an upward position to enhance
the spring return function.
To prevent the clutch bearings from unnecessary rotation,
align the input drive to the clutch through the drive flange
whenever possible.
In severe use applications, the clutch may tend to move
axially along the shaft. To prevent this axial movement,
confine the clutch between shoulders or insert spring pins
through the clutch hub into the shaft.
An optional Hub Collar is available if set screws are required
on the opposite end of the clutch. Order the Collar by
Product Number (See Table 3).
The optional Hub Collar requires drilling and tapping of
holes in the end of the clutch hub. Use the Collar as a hole
location template.
nOTe: all “5HP-SP” Clutches mount on a full shaft
using a customer supplied full length key.
A. Install Nexen’s Flexible Coupling, pulley, sprocket, or
gear (See Fig. 1 & Table 2).
B. Insert customer supplied key (See Fig. 1).
C. Slide optional Locking Hub Collar if used (See Figure
1)
D. Slide Clutch onto shaft and customer supplied key
(See Figure 1).
E. Using Set Screws (Item 20) Secure Clutch to shaft
(See Figure 1).
F. Tighten Set Screws (Item 20) to recommended torque
(See Table 4).
CAUTION
Do not connect in-line without using the Nexen
Flexible Coupling. The internal construction
of the "5HP-SP" Clutch will not allow any
misalignment tolerance. (Refer to Sales
Literature L-20208).
InSTallaTIOn (continued)
TaBle 4
L E D O M
W E R C S T E S D E D N E M M O C E R
E U Q R O T G N I N E T H G I T
P S P 0 3 H 5 . b L . n I 8 . 3 1
P S P 5 3 H 5 . b L . n I 8 . 3 1
P S P 0 4 H 5 . b L . n I 8 . 3 1
P S P 5 4 H 5 . b L . n I 8 . 3 1
P S P 0 5 H 5 . b L .t F 6 . 6
P S P 0 6 H 5 . b L .t F 6 . 6
P S P 0 7 H 5 . b L .t F 6 . 9 5
P S P 0 8 P H 5 . b L .t F 6 . 9 5