Petsafe Petporte Smart Flap® Microchip Cat Flap - Manual (Page 16)

16
Extended Modes
The Petporte smart fl ap ® ’s “extended mode” system gives you the opportunity to tailor the Petporte smart fl ap ® to your individual
requirements.
To enter the Extended Modes menu, press both the Red and Green Buttons simultaneously for 2 seconds, or until both lights begin
to fl ash, and then release them. The Petporte smart fl ap
® should beep and the green light will come on to inform you that you have
now entered the fi rst of the Extended Mode menu options.
When in “extended mode”, the modes are selected by pressing the Red Button to go “up” a mode and the Green Button to go
“Down” a mode. The current mode is indicated by a number of beeps. When you are in the mode you require, a quick press
of both buttons simultaneously will activate that mode. See page 14 for a table of available extended modes. If no buttons are
pressed within a 20 second period, the Petporte smart fl ap
® will beep and the green light will extinguish, indicating that the unit has
gone back to its normal mode of operation.
Exit Mode (leave Extended Modes) - 1 Beep
This is the fi rst mode in the Extended Mode menu. It is indicated by a single audible beep. This option simply cancels the “extend-
ed mode” and puts the Petporte smart fl ap
® back into a normal mode of operation. To activate Exit Mode, quickly press both Red
and Green buttons simultaneously.
Open Mode - 2 Beeps
In the unlikely event that you wish to have the Petporte smart fl ap
® open to allow any animal entry, the Petporte smart fl ap ® pro-
vides a mode whereby any animal (be it microchipped or not) can enter through the Petporte smart fl ap ® . Enter the extended
modes by pushing the Red and Green buttons simultaneously for more than 2 seconds then push the red button once to enter
Open Mode which will be indicated by 2 beeps. Then, to activate Open Mode and exit the extended modes quickly press both Red
and Green buttons simultaneously.
When Open Mode is activated the unit will emit a long beep and the green light should fl ash to show the unit is in Open Mode.
To de-activate Open Mode, activate the Open Mode once more. The unit will again emit a long beep and the green light should
extinguish, indicating the Petporte smart fl ap
® has returned to a normal mode of operation.
Silent Mode 3 - Beeps
Each time that a recognised animal enters or leaves via the Petporte smart fl ap
® the unit will emit a short beep. To silence this beep,
activate the Silent Mode. Enter the Extended Modes by pushing the Red and Green buttons simultaneously for more than 2 seconds
then push the red button once (the unit will emit 2 beeps) then again to enter Silent Mode which will be indicated by 3 beeps. Then to
activate silent mode and exit the extended modes quickly press both buttons simultaneously. A short beep should be heard, following
which no further beeps will be emitted whenever your pet enters or exits the Petporte smart fl ap
® .
To turn the beep back on, activate the Silent Mode once more. The unit will again emit a short beep, following which a short beep will
be emitted whenever your pet enters or exits the Petporte smart fl ap
® .
Set Light Level Mode - 4 Beeps
When the Petporte smart fl ap
® is set to Night Mode the light sensor detects a pre-determined level of ambient light and locks or un-
locks the Petporte smart fl ap ® accordingly.
If you wish to alter when the Petporte smart fl ap ® locks or unlocks in Night mode, simply activate the Set Light Level mode, in the
morning or evening, when the outside light is enough for your cat to be safely outside. Make sure that your indoor lights are switched
off when you re-set the light level; otherwise they may infl uence the light sensor. Enter the Extended Modes by pressing the Red and
Green buttons simultaneously for more than 2 seconds, then press the red button once (the unit will beep twice), then press the red
button again (the unit will beep 3 times) then press the red button once again and the unit will beep 4 times as you enter Set Light
Level Mode. To select the current light level, at which you want the door to lock or unlock, press the Red and Green buttons simultane-
ously. The unit will emit a beep and exit the Extended Modes.