Panasonic KX-TBC10 - Manual (Page 2)

S E T T I N G S
INSTALLATION/ADJUSTMENTS
2’A Installation / Instalación
1 Connect the telephone line cord to the Caller ID Box LINE connector.
Conecte el cable de línea telefónica al conector LINE del Identificador de
Llamadas.
2 Connect the telephone to the Caller ID Box PHONE connector.
Conecte el cable del teléfono al conector PHONE del Identificador de
Llamadas.
Note: Be carefu/ to correctfy connect this unit, otherwise it will not work
properly.
Note: Asegúrese de conectar correctamente esta unidad, de otra manera, no
funcionará adecuadamente.
2-B Installing Batteries i Instalación de Baterías
1 Remove the cover
Quite completamente la tapa de baterías.
2 Install three “AA’ size alkaline batteries.
Make sure to match the V" and of the batteries with the diagram inside the
compartment.
Instate tres baterías alcalinas “AA”.
Asegúrese de que ia poiaridad de ias baterías coincida con el diagrama de
poiaridad dentro dei compartimento de baterías.
3 Put the cover back in its position and push softly.
Batteries last for about four months.
Coloque la tapa de baterías en su posición origtnai y presione suavemente.
Las baterías durarán cuatro meses aproximadamente.
• Batteries not included.
• Install three “AA" high quality alkaline batteries
prior to connect to the telephone line.
• Baterías no incluidas.
• Instale 3 baterías alcalinas “AA"
antes de conectar la unidad a la
línea telefónica.
Note: Default language m this unit Is English, if by any reason the setting is in Spanish or French
and you want to return to English, please follow procedure on step BA. ___________
2-C Setting theTime and Date
If you have subscribed to the Caller ID service, the time and late are automatically set
when you receive a call.
NOTE: The year will not be adjusted. To adjust the year follow jetting the
Time and Date Manuallf steps.
Setting theTime and Date Manually
If you want to set the time and date manually, do as described below.
1
Press CALL BACK/MENU,
2 Press DOWN C2) two times to scroll to
“SETTIME-DATE’ menu,
3 Press CLEAR / SET, the “AM” icon will start flashing.
To change the icon to “PM", press UP / SELECT, CS
Repeat this procedure to go from “PM" to “AM".
4 Press CLEAR / SET again to scroll to the right on the
hour digits (Both digits will be flashing).
5 Press UP / SELECTC5D to change the hour digits.
They can be changed from 1 to 12.
6 Press CLEAR / SET again to change to the desired
minutes (The selected digit will be flashing),
7 Press UP / SELECT (3D to change the minutes
digits, the first digit can be changed from 0 to 5, the
second digit can be changed from 0 to 9,
8 Press CLEAR / SET to scroll to the month digits, the
month digits will start flashing.
9 Press UP / SELECT 3D to change the month digits,
use the same procedure to change the hour digits.
To change the day digits use the same ornnedure you
used to change the minute digits.
р«1г:ЕШ 3/15 \
aooo
SET ТХМЕ-ДЯТЕ
pvia'.oo 3/15
SHI'EII!
10 Press CLEAR / SET to scroll to the year digits, the
third digit will start flashing.
11 Press UP / SELECT 3D to change the year digit.
Use the CLEAR / SET Button to move between the
year digits. Use the UP / SELECT 3D Button to
change the flashing year digit.
Only the last two digits can be changed.
Both digits can be changed from 0 to 9.
12 When finished, press DOWN / SAVE 3D to save
the setting.
To exit from menu press CALL BACK / MENU again.
Notes:
* Do not take more than 30 seconds to replace the battenes; otherwise you will lose
all your data and settings.
, • The year will be shown when you are setting the time and date manually only.
2-D Setting the Flash Time
Note: Only if the Flash Time is requited to be different than the default 700 ms.
1 Press CALL BACK/MENU.
2 Press DOWN 3D four times to scroll until the
“FLASH* option is found.
3 Press CLEAR / SET to select the “FLASH" option.
4 Press UP / SELECT 3D to choose the flash time
from 100ms, 200ms, 300ms,.., 900ms.
5 When finished, press DOWN / SAVE CSD to save
the setting.
FLASH
PM 13 .‘QD 3/15
IGD
pm I3: dd 3/15
5Hl'E3!
To exit from menu press CALL BACK / MENU again.