Blinds Chalet Room Darkening Pleated Shades w/ No Holes Privacy - Manual (Page 2)

For shades ordered as Two-on-One Headrail using
the splicer piece, insert splicer in headrail of both
shades as shown. Lock into place using 3/8" Tek
Screws provided.
T
WO
-
ON
-O
NE
H
EADRAIL
S
PLICER
O
PTIONAL
H
OLD
D
OWN
B
RACKET
Aluminum
Splicer Piece
6"
3"
11/2
" to
2"
Optional hold down brackets are mounted
with the supplied screws. With the shade at its prop-
er drop, place the pin of each hold down into the
hole in each end
cap and mark the
screw holes. Make
sure the pins are
level and aligned.
Raise the shade,
then screw the
hold down bracket
into the mounting
surface.
Assembled Cross Section
Head Rail
Splicer
Stiffener
Fabric
C
ORDLOCK
O
PERATION
The shade fabric is easy to care for. Regular dusting
with a feather duster or vacuum cleaner brush is rec-
ommended. Most stains can be blotted with a damp
sponge and mild detergent. For problem stains, the
shade can be removed from the Installation brackets
and soaked in warm water. When damp, raise shade
tightly to re-crisp pleats. Before using anything
stronger than mild detergent and lukewarm water, test
an unobtrusive corner of the shade. If you have any
questions, call your dealer for advice.
C
LEANING AND
C
ARE
P
ROTECT
Y
OUR
C
HILDREN
To lower or release
shade, pull the cord
inward toward the
center of the shade.
To raise or lock
shade, pull the cord
straight down and out-
ward toward the edge
of the shade.
Be aware that it is possible for
children to strangle in window covering
cords. To reduce the occurrence of
accident, all cords must be kept out of
the reach of children, including infants.
Cord cleats are an effective way to
implement this essential precaution.
Mount the cord cleat at a safe height,
taking into account furniture or other
objects upon which a child may climb.
Then, after each use of the shade, simply
wrap the excess cord around the cleat. It’s fast, easy
and safe.
To protect your children, we are pleased to
provide cord cleats free of charge with every shade
that we manufacture.
The brackets are
mounted with two bugle
head screws through
the back end of the
bracket flat against
the window molding
or the wall above the
window. The bracket
requires a minimum
surface 3/4" high.
O
UTSIDE
M
OUNT
Optional extension brackets are used to project the back
of the shade up to 2 3/8" from the mounting surface.
Attach the installation bracket to the extension bracket
with the nut and bolt provided.
O
PTIONAL
E
XTENSION
B
RACKETS
2 1
/2"
3/4"
2 1/2
"
Extension
Bracket
2 1/2" minimum
Nut
Bolt
Unwind the cord from the shade but keep the rub-
ber band around the shade stack.
1. Hold the shade up near the brackets and insert
the front clip of the bracket into the front groove
of the rail.
2. Make sure the shade is centered in the window
opening.
3. Push the rail back and up until the back clips of the
bracket are inserted in the back groove of the rail.To
remove shade, reverse procedure.
H
ANGING THE
S
HADE
1. Line up the bracket top
with the desired height
of the top of the head-
rail.
2. Mark holes for
screws. Brackets
must be level.
Remove brackets
and drill holes.
3. Insert bugle head
screws for keyhole
slots only.
Approximately
1/8" of the screw
should be left
protruding.
4. Pull the cord
lock assembly
partially out of
the headrail and slide the bracket on as
shown. Push the cord lock as assembly and
bracket back all the way into the rail.
5. Remove the endcap from the opposite end
of the headrail. Slide the remaining side
mount bracket on the headrail. Replace the
end cap before sliding the bracket all the
way into the headrail.
S
IDE
M
OUNT
B
RACKET
I
NSTALLATION
Rail
6. Hook one bracket onto the screw in the window frame,
using the keyhole slot. Bring the other end bracket over
the screw at the other side of the frame. Slide down,
flexing bracket inward until the screw engages in the
keyhole slot.
7. Make sure both brackets are slipped down all the
way in the keyhole slot so that the screw is in the
top portion of the keyhole slot. Install a screw in the
bottom hole of each bracket. Tighten all screws.
3/8" Tek Screw