Caravell 635-945 - Manual (Page 8)

Classic, Classic Angle Top models English
8
• Place the products from the freezer in a cold place or pack
them in insulating material.
•
The freezer should be switched off at the socket.
•
Keep the cover open or remove the sliding covers and place
them carefully on the floor.
•
Loosen the ice layer using plastic or wooden implements
(never use metal implements).
•
The de-icing process can also be speeded up by using bowls
of hot water.
•
Never use pointed or sharp tools.
•
After de-icing, clean the cabinet as described under Section
6. Dry thoroughly after cleaning.
6 Maintenance
Please note the following in connection with the cleaning of the
freezer:
•
Place the products from the freezer in a cold place or pack
them in insulating material.
•
The freezer should be switched off at the socket.
• Keep the cover open or remove the sliding covers and place
them carefully on the floor.
The freezer can be cleaned with lukewarm water and mild
detergent. It should then be washed with clean water.
Never use detergents that contain chlorine.
Never use pointed or sharp tools.
Clean the cover in the same way as the freezer.
If the freezer has a condenser with a fan at the bottom of the
freezer, dust and dirt may gather on the cooling element. If
cleaning is required, the power should be switched off, the metal
plate under the condenser removed and the cooling element
vacuum-cleaned with a soft brush.
Remove the metal plate as follows. Use a crosstip screw driver to
remove the four screws holding the cover plate.
Afterwards, remove the metal plate in order to reach the
condenser.
Be aware that the cooling element consists of sharp components
and may be hot to the touch.
7 Troubleshooting
If you experience any problems with your freezer, please check the
following before seeking assistance:
•
Is the plug inserted?
• Is the socket switched on?
•
Is the fuse in the meter cabinet intact?
•
Has any fault current relay been disconnected?
• Has there been a complete power failure?
If the freezer is very hot or air circulation is poor, you should
provide the necessary circulation.
If the condenser is not clean, it should be vacuum-cleaned. If you
have checked the above and the freezer is still not working, call a
service technician.
State the type of fault and appliance, serial number and item no.
(stated on the manufacturer’s plate on the back of the freezer).
8 Disposal
The owner of the freezer is responsible for disposing of the freezer
in a responsible way in accordance with the current legislation.
When a worn-out freezer is to be disposed of, it should be
disposed of in an environmentally friendly and safe way.
Be aware of the rules for disposal. There may be special
requirements/regulations with which you must comply.
You can obtain information on disposal from:
•
Your dealer
•
The relevant authorities (municipal authority, Danish
Environmental Protection Agency or other similar body)
• WEEE marking.
Handling of worn-out electrical and electronic products. (Applies to
the European Union and other European countries with separate
collection systems.)
9 Special considerations
The information in this user manual was correct at the time of
printing.
Due to our programme of continuous product development, we
must however reserve the right to make technical changes to the
freezer models in this manual. We will of course endeavour
continually to update the user manual.
You should contact your dealer, who can advise your further, if you
have any doubts concerning the correct use of the freezer.
The manufacturer accepts no liability for accidents or
complications caused by the incorrect connection of the appliance.
10 Guarantee
Any guarantee will be void if the product has been misused!
This means used for purposes other than those originally intended,
failure to follow the instructions in this manual and transport of the
product not in its original packaging.
If changes are made to the freezer by unauthorised personnel, the
manufacturer accepts no liability in connection with material
damage and/or personal injury.
It is in your own interests always to use factory-authorised
personnel for any modification, repair or servicing.
The manufacturer reserves the right to make changes to
specifications without any prior notice or undertaking concerning
the availability of spare parts.