Kenwood 1080VR User Manual
Kenwood
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
KENWOOD
AUDIO VIDEO SURROUND RECEIVER
1080
VR
INSTRUCTION MANUAL
KENWOOD CORPORATION
I
I
About the supplied remote control...
Compared to standard remote controls, the remote control supplied with this receiver has several
operation modes These modes enable the remote control to perform on screen operations and control
other audio/video components. In order to effectively use the remote control it is important to read the
operating instructions and obtain a proper understanding of the remote control and how to switch its
operation modes letc,).
Using the remote control without completely understanding its design and how to switch the operation
modes may result m incorrect operations.
i
o
&
B60-3015-00 CH (K, P, Y) iVyS
98/12 11 10 9 8 7 6 5 4 3 2 1 97/12 11 10 9 8 7 6 5 4 3
Advertising
Table of contents
Document Outline
- KENWOOD
- About the supplied remote control...
- 'AC voltage selection
- Universal IR (InfraRed) remote control
- Easy surround setup and operation with OSD (On Screen Display)
- Special features
- Names and functions ofpar^
- AM loop antenna
- FM indoor antenna
- FM outdoor antenna
- FM DE-EMPHASIS/CHANNEL SPACE (Except for U.S.A. and Canada)
- Setting up the system
- Caution regarding placement (except for U.S.A. and Canada)
- Graphic equalizer
- Cassette deck or MD recorder
- CD player
- Make connections as shown below.
- The digital in jacks can accept either Dolby Digital (AC-3) or PCM signals (the input signal type is detected automatically). When connecting the related system components, be sure to also refer to the instruction manuals supplied with the components you are connecting.
- Do not connect the power cord to a wall outlet until all connections are completed.
- AC-3 RFDemodulator DEM-999D (Optional)
- SYSTEM CONTROL OPERATIONS
- SWITCHING FR0M[SL16] TO [XS8]
- Registering setup codes for KENWOOD audio components
- Setting up the system
- Preparations
- Preparing for surround sound
- Preparing for surround sound
- listening to radio broadcasts
- Listening to radio broadcasts
- Ambience effects
- Nomat playback
- Normal playback
- Listening with a graphic equalizer
- Recording a music source
- Getting the most from your remote control
- Getting the most from your remote control
- Deleting a setup code
- Checking a setup code
- Perform each step within 5 seconds.
- FutureSet allows you to update the remote control so it can operate new components which do not appear in the setup code list at the end of the manual.
- This function allows you to register new setup codes for any or all of the following command positions:
- VIDE01, VIDE02, VIDEOS, TV1, TV2, CABLE, CD, TAPE/MD.
- tíie most fmm your remote control
- Getting ttie most from your remote control
- Set up code chart
- Set up code chart
- TV Set up codes
- Ambience effects
- To select a DSP mode
- To adjust the DSP modes
- O Select a parameter.
- © Adjust the parameter using the TUNING/SKIP keys on the remote control.
- © Press MAIN to return to the main sound menu or press the SOUND key on the remote to turn of! the on-screen display.
- O Press either VIDEO, AUDIO, or TV key on the remote to cancel the OSD remote control mode.
- Convenient functions
- Ambience eflects
- OSD switch
- SOURCE DIRECT switch
- SET UP switch
- RADIO TEXT switch
- LISTEN MODE key
- SUBWOOFER adjustment
- Low battery warning
- Find the setup code of the component to he registered.
- Hold down the ENT key until the backlight flashes twice and remains lit.
- Select the component to be registered.
- Enter the setup code.
- Press the ENT key.
- Repeat steps 3 to 6 to register additional components until all components have been registered.
- Once setup codes have been entered for all components, hold down the ENT key until the backlight flashes twice.
- Getting the most from your remote controt
- SmfÊRiaâMâmsMsmsÉm.
- Press the MACRO key.
- Execute the macro play.
- FutureSet allows you to update the remote control so it can operate new components which do not appear in the setup code list at the end of the manual.
- This function allows you to register new setup codes for any or all of the following command positions:
- VIDE01, VIDE02, VIDEOS, TV1, TV2, CABLE, CD, TAPE/MD.
- USA: 1-800-753-9860 Canada: 1-800-644-0673
- Hold your remote to the speaker portion of your telephone.
- Code selection after mode download
- Non-IR codes
- VCR Set up codes
- VCR Set up codes (continued)
- TV Set up codes
- Set up code chart
- TV Set up codes (continued)
- Satellite Set up codes
- LD player Set up codes
- DSS Set up codes
- DVD Set up codes
- Cable Set up codes
- CD Player Set up codes
- Cassette deck Set up codes
- MD Set up codes
- Resetting the Microcomputer
- Amplifier
- Tuner
- Remote control unit
- For the U.S.A.
- Memory back up function
- For the U.S.A.
- DSS receiver operations
- Remote operation of other components "i