Crosman ASP9T - Manual

Stinger P9T
6 MM AIRSOFT PISTOL
6 MM PLASTIC BB
OWNER’S MANUAL
Distributed by
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
www.crosman.com
1-800-724-7486
Made in Taiwan. ASP9TB515
WARNING: This is not a toy. Adult supervision is required. Misuse may cause serious
injury, especially to the eye. Eye protection designed for airsoft guns must be worn by the
user and any person in range. May be dangerous up to 100 yds. Read the owner’s manual
before using.
WARNING: Do not brandish or display this airsoft gun in public – it may confuse people
and may be a crime. Police and others may think it is a firearm. Do not change the coloration
and markings to make it look more like a firearm. That is dangerous and may be a crime.
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE
AND OWNERSHIP OF THIS AIRSOFT GUN.
Recommend 18 years or older to purchase. Intended for use by those 16 or older.
Please read this owner’s manual completely. Remember to treat this airsoft gun with the same respect you would a
firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this manual in a safe
place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman Customer Service at: 1-800-
724-7486, 585-657-6161 or www.crosman.com.
1. Learning the Parts of Your New Airsoft pistol
Learning the names of the parts of your new airsoft pistol will help you to understand your owner’s manual. Use this
manual to increase your enjoyment of this airsoft pistol.
A B C D
F
G
H I
J
L
A. Front Sight
B. Slide
C. Breech
D. Rear Sight
E. Slide Release Lever (see Fig. 6)
F. BB Clip
G. Grip Frame
H. Clip Release Lever
I. Trigger
J. Trigger Guard
K. Safety (see Fig. 2A and 2B)
L. Muzzle
2. Operating the Safety
A. To Put the airsoft pistol “ON SAFE”
• Locate the safety on the right side of the airsoft gun.
• Push the all the way forward toward the “S”, for “ON SAFE” (Fig. 2). The safety is not “ON SAFE” unless it is
pushed all the way forward.
WARNING: Keep the airsoft pistol in the “ON SAFE” position until you are actually
ready to shoot. Then turn the safety to the “OFF SAFE” position.
Like all mechanical devices, an airsoft gun safety can fail.
Even when the safety is “ON SAFE”, you should continue to
handle the airsoft gun safely.
NEVER point the airsoft gun at any person. NEVER point
the airsoft gun at anything you do not intend to shoot.
B. To Take the Airsoft pistol “OFF SAFE”
• Locate the safety on the right side of the airsoft gun.
• Push the safety all the way backward toward the “F” for
“OFF SAFE”. When the safety is all the way back the
airsoft gun is “OFF SAFE” and can be fired.
3. Loading and Unloading Plastic BBs
A. Loading
WARNING: Use 6 mm plastic BBs only in this airsoft pistol. Use of any other ammuni-
tion can cause injury to you or damage to the airsoft pistol.
• Make sure the airsoft pistol is “ON SAFE” (section 2A).
• Point the airsoft pistol in a SAFE DIRECTION.
• While supporting the BB clip, push the clip release lever down and remove the clip.
• Pull and hold down the BB follower tab (fig. 3)
• Insert up to 15 plastic BBs into the BB loading hole on the front of the maga-
zine (fig 4).
• Place a finger over the end of the magazine where the BBs will exit (fig 5).
• With the magazine pointed in a safe direction, release the BB Follower tab.
NOTE: Releasing the BB follower tab quickly, or without the end covered, could
allow BBS to exit the magazine.
• Insert the loaded clip into the airsoft gun
• Your airsoft gun is now loaded and ready to fire, after reading the entire manual, including sec-
tion 8 on reviewing safety.
• As you use up the BBs you will need to repeat the steps for loading the BBs. BBs will not
automatically fill from the reservoir into the magazine area.
B. Unloading Plastic BBs
• Make sure the airsoft pistol is “ON SAFE” (section 2A).
• Point the airsoft pistol in a SAFE DIRECTION.
• While supporting the BB clip, push the clip release lever down and remove the clip.
• Pull down the BB retainer button and lock in place
• Tip the clip until the BBs empty out of the slotted magazine area.
• Release the BB retainer button.
WARNING: Never assume that because the airsoft pistol no longer fires a BB and/or
the clip is removed, that a BB is not lodged in the barrel. Always treat the airsoft pistol as
though it is loaded and with the same respect you would a firearm.
4. Cocking your Airsoft pistol
• Make sure the airsoft pistol is “ON SAFE” (section 2A).
• Point the airsoft pistol in a SAFE DIRECTION.
• While holding the airsoft pistol in a horizontal position, cock by firmly holding
the slide with your entire hand, pulling the slide rearward and releasing in a
smooth motion (Fig. 6).
NOTE: While shooting the gun when the magazine empties the slide will remain in
the rear position as you attempt to cock and release it. Though the slide remains in
the rear position you should not use this as an indicator if the gun is loaded or not.
Continue to follow rules of safe gun handling.
• To release the slide put the gun “ON SAFE” and press the slide release lever on the left side of the gun.
5. Aiming and Firing Safely
• You and others with you should always wear shooting glasses to protect your eyes.
• Always point your airsoft pistol in a SAFE DIRECTION.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off
or ricochet and hit someone or something you had not intended to hit. If the plastic BBs
should happen to hit a hard surface, DO NOT re-use those plastic BBs because they
could possibly cause damage to your airsoft pistol.
• Your airsoft pistol is designed for target shooting and is suited for both indoor and out-
door use. Always remember to place your target carefully. THINK about what you will hit if
you miss the target.
• Your airsoft pistol is correctly aimed when the front sight blade is position exactly in the
notch of the rear sight. The top of the front sight blade should be even with the top of the
notch in the rear sight. The bulls-eye should appear to rest on the top of the front sight
(Fig. 8).
• When you are sure of your target and backstop, and the area around the target is clear,
load and cock the airsoft pistol following sections 3 and 4. Take the airsoft pistol “OFF
SAFE” (section 2A) aim and pull the trigger to fire.
6. Maintaining Your Airsoft pistol
• DO NOT MODIFY OR ALTER YOUR AIRSOFT PISTOL. Tampering with the airsoft pistol or attempts to change the
airsoft pistol in any way may make it unsafe to use, may cause serious injury or death and will void the warranty.
• If you drop your airsoft pistol, visually check to see that it works properly before you use it again. If anything
seems changed, like a shorter or weaker trigger pull, this may mean parts are worn out or broken. Call Cus-
tomer Service at Crosman for assistance before using your airsoft pistol again.
7. Clearing a Jam
Never look down the end of barrel to see if a jam has been cleared.
• Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
• Remove the magazine
• Insert the tapered end of the cleaning rod into the barrel, with the angle toward the breech (where the magazine
connects).
• CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
• Reinstall the magazine and test gun.
8. Reviewing Safety
Fig. 2A Fig. 2B
Fig. 3 Fig. 4
Fig. 5
Fig. 6
• Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend
to shoot.
• Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airsoft gun pointed in a SAFE DIRECTION.
• Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
• Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear eye protection to protect your eyes.
• Always wear eye protection designed for airsoft over your regular glasses.
• Use 6 mm plastic BBs only.
• Do not reuse plastic BBs because they could cause possible damage to your airsoft gun.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit
someone or something you had not intended to hit.
• Replace the backstop if it becomes worn. Place the backstop in a location that will be safe should the backstop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and will
eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way may make
your airsoft gun unsafe to use, cause serious injury or death and will void the warranty.
• Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and
will void your warranty.
• Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
• Always store this airsoft gun in a secure location.
SPECIFICATIONS
Mechanism/Action Spring air repeater Overall Length 7 1/8” inches
Caliber/Ammunition 6mm Plastic BBs Barrel Smooth
Magazine Up to 15 6 mm BBs Safety Slide
Weight 10 oz Velocity Up to 230 fps (70 m/s)
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile and barrel condition.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives will help. You can get answers to frequently asked
questions at www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800-
724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO
DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no
warranty responsibility under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may
cause your product to malfunction and may void your warranty.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material
and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform
normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL
EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, Bloomfield, NY 14469.
Canadian Customers: Contact the Gravel Agency 418-682-3000 X46
International Customers: Please return product to your nearest distributor. If you do not know your distributor,
please call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be pre-
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.