Crosman CP02 - Manual

Model CP02
6mm CO
2
Airsoft BB Repeater
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN
Marine Corps trademarks used under license by Crosman Corporation.
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
www.crosman.com
1-800-724-7486
Made in Taiwan P/N MCCP02A515
WARNING: This is not a toy. Adult supervision is required. Misuse may cause serious
injury, especially to the eye. Eye protection must be worn by the user and any person in range.
May be dangerous up to 100 yds. Read the owner’s manual before using.
WARNING: Do not brandish or display this airsoft gun in public – it may confuse
people and may be a crime. Police and others may think it is a firearm. Do not change the
coloration and markings to make it look more like a firearm. That is dangerous and may be
a crime. READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING
THIS AIRSOFT GUN.
WARNING:
This product contains a chemical known to the state of California to cause
cancer and birth defects (and other reproductive harm).
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR EYE PROTECTION TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND
OWNERSHIP OF THIS AIRSOFT GUN.
Recommend 18 years or older to purchase. Intended for use by those 16 or older.
Please read this owner’s manual completely. And remember, this airsoft gun is not a toy. Treat it with the same respect
you would a firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this manual
in a safe place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman at 1-800-724-7486, 585-657-6161
or www.crosman.com.
1. Learning the Parts of Your New Airsoft gun
Learning the names of the parts of your new airsoft gun will help you understand your owner’s manual. Use this
manual to increase your enjoyment of this airsoft gun.
A. Front sight
B. Muzzle
C. Slide
D. Breech
E. Rear Sight
F. Grip
G. Magazine
H. Trigger Guard
I. Trigger
J. Magazine Release Button
K. Safety (fig. 2)
L. Piercing Knob (fig. 4)
2. Operating the Safety
A. To Put the Airsoft Gun “ON SAFE”
• Locate the safety at the bottom of the backside of the grip. (Fig 2A)
• Pull the safety down all the way to “ON SAFE” (Fig. 2A). The safety is not “ON SAFE”
unless it is pulled all the way down.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is
“ON SAFE”, you should continue to handle the airsoft gun safely.
NEVER point the airsoft gun at any person. NEVER point the airsoft gun at anything
you do not intend to shoot.
B. To Take the Airsoft gun “OFF SAFE”
WARNING:
Keep the airsoft gun in the “ON SAFE” position until you are ready to shoot.
Then turn the safety to the “OFF SAFE” position.
• Locate the safety at the bottom of the backside of the grip. (Fig 2B)
• Push the safety up all the way to “OFF SAFE” (Fig. 2B). The safety is not “OFF SAFE” unless it is pushed all the way up.
3. Installing and Removing the CO
2
Cartridge
A. Installing a New CO
2
Cartridge
WARNING:
CO
2
cartridges may explode at temperatures above 120°F (48.9°C). Do not
mutilate or incinerate them. Do not expose them to heat or store CO
2
cartridges at tempera-
tures above 120°F (48.9°C).
• Put the airsoft gun “ON SAFE” (see Section 2A) and point in a SAFE DIRECTION.
• With your hand under the magazine, press the magazine release button. (Fig 3)
• To remove the piercing cap, use the enclosed hex wrench and turn counter clockwise.
• Insert the new CO
2
cartridge into the airsoft gun with the small neck of the CO
2
car-
tridge inserted first.
• Using the hex wrench, tighten the cartridge piercing knob by turning it clockwise. If
you hear a hissing sound when piercing the gun, tighten the piercing cap more.
• To make sure the cartridge has been pierced, point the airsoft gun in a SAFE DIREC-
TION, and cock it by pulling the slide all the way back to the rearward position and
slowly allowing it to move forward.
• Take “OFF SAFE” (see Step 2B) and pull the trigger.
• Return the gun to the “ON SAFE” position (section 2A).
• If the airsoft gun does not make a popping noise after pulling the trigger, the CO
2
is not
being discharged. In that event put the airsoft gun “ON SAFE” (Step 2A), and tighten
the piercing knob 1/4 turn.
• Point the airsoft gun in a SAFE DIRECTION, take “OFF SAFE” (see Step 2B) and pull
the trigger.
• Repeat this process until the CO
2
is discharged when you pull the trigger.
NOTE: We recommend the use of Crosman ® Powerlet ® 12g CO
2
cartridges. They are
made to fit your airsoft gun. Other brands of CO
2
cartridges may not fit properly and
if forced into place, may result in injury to you or damage to your airsoft gun. Never
force any CO
2
cartridge into or out of place.
Do not store your airsoft gun with a CO
2
cartridge in it. If you know you will not be using your airsoft gun for an ex-
tended period of time, empty the CO
2
cartridge and remove it from the airsoft gun (Step 3B).
This is an important step as it will prolong the longevity of your airsoft gun seals.
B. Removing CO
2
Cartridge
WARNING:
Keep hands away from escaping CO
2
gas. It can cause frostbite if allowed
to come in contact with skin. Always make sure the CO
2
cartridge is empty before attempt-
ing to remove it from the airsoft gun by slowly turning the knob counter-clockwise all the way
until you no longer hear the escape of CO
2
gas.
• Put the airsoft gun “ON SAFE” (section 2A) and point in a SAFE DIRECTION.
• With your hand under the magazine, press the magazine release button. (Fig 3)
• Use the enclosed hex wrench to slowly turn the piercing cap counter clockwise, allowing any remaining gas to escape.
(Fig 4)
• Remove the cap and drop out the CO
2
cartridge.
• Replace the piercing cap when the gun is not in use.
4. Loading and Unloading Airsoft BBs
A. Loading Airsoft BBs
• Put the airsoft gun “ON SAFE” (section 2A) and point in a SAFE DIRECTION.
• With your hand under the magazine, press the magazine release button. (Fig 3)
• Pull and hold down the BB follower tab (Fig 5)
• Insert up to 26 airsoft BBs into the BB loading hole on the front of the magazine.
• Place a finger over the end of the magazine where the BBs will exit.
• With the magazine pointed in a safe direction, release the BB follower tab.
NOTE: Releasing the BB follower tab too quickly, or without the end covered, may
allow BBs to exit the magazine.
• Your airsoft gun is now loaded and will be ready to fire, after reading the entire
manual, including section 7 on reviewing safety.
NOTE: This airsoft gun has been developed with a blowback feature, which allows the gun to automatically re-cock
after each trigger pull. You need only cock your air pistol manually once when you load the CO
2
.
ADDITIONAL INFORMATION ABOUT THE BLOWBACK FEATURE
EMPTY CLIP
When the clip is empty, the airsoft gun will not fully re-cock, and the slide will remain in the rearward position. To con-
tinue shooting, place the gun “ON SAFE” and reload BBs following section 4A. Release the slide by pressing the slide
release lever. The airsoft gun is cocked and ready to fire after taking “OFF SAFE”.
EMPTY CO
2
CARTRIDGE
As the CO
2
is consumed, the cartridge may not have enough CO
2
to re-cock the airsoft gun, and the slide may remain
in the forward position. Put the airsoft gun “ON SAFE” and follow section 3B on removing the CO
2
cartridge.
NOTE: The faster you shoot the gun, the faster you will use up the CO
2
. For OPTIMUM CO
2
EFFICIENCY pause 5
seconds between shots.
B. Unloading Airsoft BBs
• Put the airsoft gun “ON SAFE” (See Step 2A).
• Point the airsoft gun in a SAFE DIRECTION.
• Remove the magazine by pressing on the magazine release button.
• Pull and hold down the BB follower tab.
• If a BB is still visible in the top of the magazine, push the BB out of the magazine.
• Aim the airsoft gun in a SAFE DIRECTION; insert the magazine into the gun, take it
“OFF SAFE” (See Step 2B) and fire.
• Repeat this procedure several times until you are sure you are no longer firing BBs.
NOTE: The airsoft gun must be charged with CO
2
when following these steps but
remember, do not store your airsoft gun with a CO
2
cartridge in it.
WARNING: Even though you go through the unloading procedure, continue to treat the
airsoft gun as though it were loaded. Do not point at anything you do not intend to shoot.
Adjusting the Hop- up
Your airsoft gun is manufactured with an adjustable hop-up system. The purpose of
this system is to change the spin on the BB as it leaves the muzzle, allowing you to
adapt your shot for different distances.
• Put the airsoft gun “ON SAFE” (see Section 2A) and point in a SAFE DIRECTION.
• With your hand under the magazine, press the magazine release button and put the
magazine aside.
• Press in, pull down and hold the slide lock button while moving the slide back, and
then, move it forward to remove. (Fig 6A)
• Use the smaller included hex wrench to turn the hop-up adjustment screw- turn clock-
wise for more hop-up, turn counter-clockwise for less. (Fig 6B)
• Verify the recoil guide is in properly (Fig 6C)
• Starting at the back of the gun, line the slide up with the gun (Fig 6D & (Fig 6E) and pull
slide forward.
5. Aiming and Firing Safely
• You and others with you should always wear eye protection to protect your eyes.
• Always point your airsoft gun in a SAFE DIRECTION.
• Do not shoot at hard surfaces or at the surface of water. The airsoft BBs may bounce
off or ricochet and hit someone or something you had not intended to hit.
• DO NOT re-use airsoft BBs because they could possibly cause damage to your airsoft gun.
• Your airsoft gun is designed for target shooting and is suited for both indoor and out-
door use. Always remember to place your target carefully. THINK about what you will
hit if you miss the target.
• Your airsoft gun is correctly aimed when the front sight blade is positioned exactly in
the notch of the rear sight. The top of the front sight blade should be even with the
top of the notch in the rear sight. The bulls-eye should appear to rest on the top of the
front sight (Fig. 7). .
• When you are sure of your target and backstop, and the area around the target is clear,
take the airsoft gun “OFF SAFE” (section 2A) aim and pull the trigger to fire.
6. Maintaining Your Airsoft gun
• Putting 1 drop of Crosman 0241 Pellgunoil ® on the tip of every CO
2
cylinder will help to
maintain your airsoft gun. DO NOT use petroleum distillate based oil or solvent and DO
NOT over-oil as this can cause damage to your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft
gun in any way inconsistent with this manual may make your airsoft gun unsafe to use,
cause serious injury, especially to the eye and will void the warranty.
• If you drop your airsoft gun, check to see that it works properly before you use it again.
• If anything seems changed, like a shorter or weaker trigger pull, this may mean worn
out or broken parts. Call Crosman customer service for assistance before using your
airsoft gun again.
A. How to clean the magazine
• Remove the magazine.
• Wipe down the outside of magazine.
• Spray a small amount of Crosman Nitro Lubricant oil into the BB tube.
• Replace the magazine.
B. To clean the Airsoft gun barrel
• Spray a cleaning patch with Crosman Nitro Lubricant oil.
• With the patch on the rod, insert the rod into the barrel to clean.
• Swab the barrel 3-4 times.
• Repeat the swabbing procedure with a dry patch.
• The barrel is clean when patches come out clean after dry swabbing.
C. Lubricating Parts
• After each 2000 shots, use silicone lube spray such as Crosman’s Lightening Lube to spray the moving parts.
D. Clearing a Jam
• Never look down the end of barrel to see if a jam has been cleared.
• Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
• Remove the magazine.
• Insert the tapered end of the cleaning rod into the barrel.
• CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
• Reinstall the magazine and test the gun.
7. Reviewing Safety
• Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend to shoot.
• Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airsoft gun pointed in A SAFE DIRECTION.
• Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
• Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear eye protection to protect your eyes.
• Always wear eye protection over your regular glasses.
• Use 6 mm plastic BBs only.
• Do not reuse plastic BBs because they could cause possible damage to your airsoft gun.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit someone or
something you had not intended to hit.
• Replace the backstop if it becomes worn. Place the backstop in a location that will be safe should the backstop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and will eventu-
ally fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFTGUN. Attempts to modify the airsoft gun in any way may make your airsoft
gun unsafe to use, cause serious injury or death and will void the warranty.
• Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and will void your
warranty.
• Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
• Always store this airsoft gun in a secure location.
SPECIFICATIONS
Mechanism Semi-Automatic Blowback
Sights
Front: Fixed Blade
Rear: Fixed Notch
Caliber/Ammunition 6 mm Plastic BB
Power Source 12 gram CO
2
cartridge Capacity Up to 26 BB
Length 8.125 inches Velocity Up to 320 fps
Weight 2 lbs Safety Lever
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile, amount of CO
2
and
barrel condition.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives will help. You can get answers to frequently asked questions at www.crosman.
com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800-
724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO DISAS-
SEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no warranty
responsibility under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may cause
your product to malfunction and may void your warranty.
LIMITED 90 DAY WARRANTY
This product is warranted to the retail consumer for 90 days from date of retail purchase against defects in material
and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform normal
maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL EX-
PENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, Bloomfield, NY 14469.
International Customers: Please return product to your nearest distributor. If you do not know your distributor,
please call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITA-
TIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempt-
ed, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.
Check out our complete line of Marine Corps airsoft products at marinesairsoft.com
For more information about the Marine Corps and becoming a Marine, visit marines.com
Officially Licensed Product of the United States Marine Corps, www.marines.com and 1.800.marines.
Fig 7