Dynaflite GPMA0090 Butterfly - Manual (Page 4)

4
❍ O.S.
® 10LA (OSMG0011) or O.S. 15LA
(OSMG0016)
❍ Engine Mount (Hayes 006-AS15 short
mount for O.S. LA engines) HAYG0006
❍ Propellers; Refer to your engine’s
instructions for proper size
❍ Approximately 2 rolls Top Flite MonoKote ®
covering; See Covering Tips (page 31)
❍ Medium Fuel Tubing (3’, GPMQ4131)
❍ 1/4" Latex Rubber Padding (HCAQ1000)
❍ 1/16" Foam Wing Seating Tape
(GPMQ4422)
❍ 4 oz. Fuel Tank
❍ (2) 2-1/4" Wheels (GPMQ4222)
❍ (4) 4-40 x 1/2" screws to secure engine
mount (GPMQ3012)
❍ (4) 4-40 blind nuts for engine mount
screws (GPMQ3324)
❍ #64 Rubber Bands (1/4 lb box –
HCAQ2020)
❍ (4) 5/32" Wheel Collars (GPMQ4306)
❍ #4 x 1/2" Screw for mounting engine to
engine mount
Setting Up Shop
If this is your fi rst model there are a few supplies
and tools that you should gather before you begin.
The most important item is a fl at table that you can
build your models on. You can turn a solid core door
into a building table, but avoid hollow core doors
because they warp easily. If possible, locate your
building table in an area that is not in the way of
other projects or household activities. Cover your
building table with a board that you can stick pins
into. The back of a 2’ x 4’ ceiling tile works well or
you can cut a piece to fi t your table from a 4’ x 8’
sheet of Celotex insulation board available from a
home improvement store.
Required Supplies and Tools
These are the building tools and adhesives that
you will need to build your Butterfl y.
We recommend Great Planes Pro ™ CA and Epoxy
❍ 2 oz. Thin CA Adhesive - (GPMR6003)
❍ 2 oz. Medium CA+ (GPMR6009)
❍ CA Activator - (GPMR6035)
❍ 30-Minute Epoxy - (GPMR6047)
❍ #1 Hobby Knife Handle (XACR4305)
❍ #11 Blades (Qty. 100 – HCAR0311) or (Qty.
5 – XACR2911)
❍ X-Acto
® (or similar) Building Square
(XACR7726) or Building Triangle
(XACR7725)
❍ Medium T-pins (HCAR5150)
❍ Wax Paper
❍ Electric Drill
❍ Drill Bits: 1/16", 5/64", 3/32", 3/16", 11/64"
or 5/32", 15/64" or 1/4"
❍ String for aligning the stabilizer
❍ Screwdrivers (Phillips and Flat Blade)
❍ Top Flite Covering Iron (TOPR2100)
❍ A building board that you can stick pins
into (see “Setting Up Shop”)
Optional Accessories
You can build your Butterfl y without these items
but they will make the job much easier and provide
you with better results. These are things you will
accumulate as your building “career” progresses
anyway.
❍ Razor Plane (MASR1510)
❍ Single-Edge Razor Blades (100,
HCAR0312)
❍ CA Applicator Tips (HCAR3780)
❍ Hot Sock
™ (for your covering iron,
TOPR2175)