Adjustable sticks, Charge jack, Trainer function – Flyzone FLZA4032 User Manual

Page 15

Advertising
background image

15

aircraft could result. Replace weak alkaline batteries,
or re-charge NiCd or NiMH batteries, before attempting
a fl ight!

If during a fl ight the Tx LED starts to fl ash, accompanied
by the sounding of audible tones, it’s a warning that the

Tx batteries have become weak and the aircraft should be

landed as soon as possible!

Adjustable Sticks

The length of both gimbal

sticks can be adjusted as
desired. Loosen the set
screw inside the center of the
stick with a 2mm hex wrench.
Rotate the stick end counter-
clockwise to lengthen the stick,

or clockwise to shorten the stick. Once the desired stick
length is found, tighten the set screw with the hex wrench.

Charge Jack

WARNING!! Do NOT attempt to recharge

alkaline batteries! The charge jack should

ONLY be used if rechargeable cells are used in the
transmitter.

The TTX600 includes a built-in charge jack for convenient

recharging of NiCd or NiMH batteries, and is compatible
with charge leads designed for Futaba

®

brand transmitters

(HCAP0101). This jack is NOT compatible with charge leads

for Hitec

®

, Airtronics

®

, JR

®

or Spektrum

®

radios.

To use the charge jack with optional rechargeable batteries,

fi rst remove the sticker that covers the charge jack on the
side of the Tx – making sure not to allow any object to be

inserted inside the jack itself. Next, insert the cells inside
the Tx’s battery compartment noting proper polarity. Make
sure the transmitter’s power switch is in the OFF position.

Connect a compatible charge lead to the jack and follow the

instructions included with the charger for charging of NiCd or
NiMH batteries that are rated at 4.8V.

Tactic’s optional TACP1000 rechargeable battery and wall

charger kit includes eight “AA” size rechargeable NiMH cells
and 110V AC wall charger, which is compatible with this Tx
and can be found at local retailers. Make sure to follow the
instructions included with the charge kit.

WARNING!! It’s not recommended to charge

batteries at greater than 1 amp through this
charge jack. Fast charging of NiCd and
NiMH batteries should ONLY be done with

chargers that are specifi cally designed to include the
peak-detection function which can automatically stop
charge when full charge is detected. Misuse, improper
charging, or over-charging of rechargeable cells can
result in damage to the cells that could include cell
rupture, explosion, or fi re!!

Trainer Function

The TTX600 Tx includes a built-in wireless trainer function

– no trainer cable required! This trainer system connects a

teacher’s Tactic Tx to a student’s Tactic Tx by wireless
connection. Tactic’s wireless trainer function is not compatible
with trainer systems in any other brand radios.

IMPORTANT! Before attempting to fl y the
airplane, it’s very important to make sure all
reversing switches and trim lever adjustments
on the student’s Tx match the settings on the

teacher’s Tx! Otherwise, the airplane could suddenly veer
off in an unwanted manner when the teacher’s trainer switch
is pressed. Proper matching of the student and teacher’s

Tx settings should ensure that no unexpected movements

occur when the trainer switch is pressed. This is especially
true of the throttle control!

1. The Tx that was used to set up the controls on the

aircraft must be used by the TEACHER.

2. The student must use a separate Tactic Tx with

wireless trainer function.

3. Place the teacher’s and student’s transmitters within

1 meter of each other, and make sure the throttle

stick for each Tx is set to idle.

4. Turn ON the power switch for the Tx being held by

the student.

5. Pull and hold the trainer switch on the teacher’s Tx,

and then turn ON the teacher’s Tx power switch.

6. The LED on the teacher’s Tx will fl ash 3 times to

indicate it has become bound with the student’s Tx.

7. The teacher can then release his trainer switch.

8. Once both transmitters are bound together, power

can be applied to the receiver to prepare for fl ight.

When the training session has ended, with the model on the

ground and all power removed from the model, place both
transmitters within 1 meter of each other and simply turn the
power switch for both transmitters to the OFF position. This
will terminate the wireless link between both transmitters. If
additional training will be performed again, return to step 1
above to re-establish the wireless link between the teacher
and student’s transmitters.

Advertising
This manual is related to the following products: