Futaba 10C 2.4GHz - Manual (Page 36)

36
Adjustable travel limit (ATL): makes the channel 3 TRIM LEVER (THROTTLE TRIM) effective only at low throttle,
disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON.
If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set ATL
to OFF. If you need the ATL to be effective at the top of the stick instead of the bottom, reverse the THR-REV setting. Note
that this affects all models in the radio, not just the model you are currently editing. See servo REVERSE, p. 38.
GOAL of EXAMPLE: STEPS: INPUTS:
Change ATL from ON to OFF for battling
robot, tank, airbrake and other channel
3 uses. O p e n B A S I C m e n u , t h e n o p e n
PARAMETER
submenu.
for 1 second. (If ADVANCE, again.)
to 2nd page of menu.
C to PARAMETER.
Go to ATL and Change. (Ex: to OFF) C to ATL. to OFF.
Close.
Where next? Set up ELEVON IRUWDQNVW\OHFRQWUROWKURWWOHVWHHULQJRQRQH67,&. VHHS
Set up IDLE-DOWN and THR-CUT to adjust channel 3 servo at low-stick: see p. 40.
5HDVVLJQDX[LOLDU\FKDQQHOV H[ IURPGLDOWRVZLWFKVOLGHU VHHS
Utilize servo REVERSE: see p. 38.
Adjust servo travel with END POINT: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Second aileron (AILE-2) (ACRO GLID 1A+1FGLID 2A+1F only): changes the default choice for dual aileron servos from
channels 6 (FLAPERON) to channels 5 and 6, or 7(AIL-DIF ) to channels 5 and 7. This allows you to utilize these 2 great
functions while utilizing a 5-channel receiver.
NOTE: Changing AILE-2 only tells the system which servos to utilize if FLAPERON or AIL-DIF is activated. You still must
activate that function and complete its setup. For details on twin aileron servos, including using AILE-2, see p. 55.
LCD screen adjustment (CONTRAST BACK-LIGHT):
Adjustability:
The following LCD screen adustments are possible.
• Contrast adjustment
• Backlighting brightness adjustment
CONTRAST : set a LCD contrast from +10(dark) to -10(bright). Also it can be set from the home screen. See Adjusting
Display Contrast, p.16.
BACK-LIGHT MAX
VHWDEDFNOLJKWLQJEULJKWQHVVIRUWKHVSHFL¿FSHULRG DSSUR[LPDWHO\VHFRQGV DIWHURSHUDWLQJWKHHGLW
keys. Setting range: OFF(0) to 20(bright).
BACK-LIGHT MIN
VHWDEDFNOLJKWLQJEULJKWQHVVDIWHUWKHDERYHVSHFL¿FSHULRG6HWWLQJUDQJH 2))  WRMAX setting.
GOAL of EXAMPLE: STEPS: INPUTS:
Change CONTRAST from 0 to +2. O p e n B A S I C m e n u , t h e n o p e n
PARAMETER
submenu.
for 1 second. (If ADVANCE, again.)
C to PARAMETER.
Go to CONTRAST and change setting.
(Ex: +2) C to CONTRAST.
to +2.
Close.