GME TX3345 - Manual (Page 15)

NOTE: If the call is not sent within 10 seconds of entering
the last Ident digit the Call function will time-out and the
radio will return to normal mode. To exit the mode without
sending the SelCall briefly press the CALL button.
CALL ACKNOWLEDGE
If your SelCall transmission is successful, the radio you
called should respond with an ‘acknowledge’ signal –
usually two quick beeps. This will confirm to you that the
radio you called is now alerting its user to your signal.
SELCALL MEMORIES
Your radio is fitted with a ‘Call’ memory, an ‘ID’ memory
and 10 user programmable storage memories as follows:
1. ‘Call’ memory – always holds your last-sent SelCall
Ident making it easy to resend it.
2. ‘Id’ memory – holds your radio’s own SelCall Ident.
You should only select this memory location if you need
to change your radio’s factory programmed SelCall Ident.
3. User programmable storage memories – can be
used to store and recall frequently called SelCall Idents.
Memories are labelled ‘C0’ to ‘C9’.
To store a SelCall Ident in memory
1. Briefly press the CALL button. is displayed along
with the last sent or received SelCall Ident.
2. Press the or keys to select the required
memory location ‘C0’ to ‘C9’ (to change your radio’s
own SelCall Ident, select ‘Id’). If an ALPHA label is
displayed you will need to press
MENU
F
then SQL
ALPHA
to
switch to Numeric Mode.
3. Press and hold the LVL
PRI
key until the radio beeps. The
right-hand digit of the SelCall Ident will flash.
4. Press the or keys to select the required
number in the flashing digit position.
5. Briefly press the LVL
PRI
key again to select the next digit
position.
6. Repeat steps 4 and 5 to enter all 5 digits as required.
7. Now press and hold the LVL
PRI
key. The entire Ident will
flash for a few seconds then the radio will beep as the
new Ident is stored.
Recalling SelCall Idents from memory
1. Briefly press the CALL button. is displayed along
with the last sent or received SelCall Ident.
2. Press the or keys to select the required Ident
memory in locations ‘C0’ to ‘C9’.
3. Press and hold the CALL button to send the Ident.
Changing your radio’s own SelCall Ident
1. Ensure your radio is in Numeric Mode (press MENU
F
then
SQL
ALPHA
as required until ‘NUMER’ is displayed).
2. Briefly press the CALL button. is displayed along
with the last sent or received SelCall Ident.
3. Press the key. ‘Id’ will be displayed along with
your radios own SelCall Ident.
4. Press and hold the LVL
PRI
key until the radio beeps.
The right-hand digit of the SelCall Ident will flash.
5. Press the or keys to select the required
number in the flashing digit position.
6. Briefly press the LVL
PRI
key again to select the next
digit position.
7. Repeat steps 5 and 6 to enter all 5 digits as required.
8. Now press and hold the LVL
PRI
key. The entire Ident will
flash for a few seconds then the radio will beep as the
new Ident is stored.
LABELLING YOUR SELCALL IDENTS
You can label each SelCall Ident using a 5 character name
to make it easier to identify callers. If an incoming SelCall
matches one of those in your radio’s memory, the label can
be displayed instead of the SelCall Ident.
T X 3 3 4 5 I N S T R U C T I O N M A N UA L PA G E 1 5
46397-2_TX3345_InsMan.indd 15 11/09/13 12:04 PM