Philips AJ 3940/05 - Manual

“О
о (/)
<£>
' Q
О
° ~ 0 о о ° о о о о° о °
п О О О о О о О О О о ^ О
о
°о°о О
о
о%Оо°° о
о о °
о ° о о о п о о о о о о о о „ о °
^ ° 0 ° 0 ° п о о о о О О О д О о
JQ ^Оп°°0
^Оо°о§^^
"о о о°°о°п
^ 0^0° o'- ооО
п О ^ .
________________ о'^о“0—U U U U
°о°ооО. о о о .о
.0^-4 л
Лг
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
o o o o o
°0°°ooo
S°°Oo
“o°O°°0
7(o°o°§o„°0
AVIS I NEWSOUVRÌF
RISQUE DU CHOC ELECTRIQUE
®
■
®
.®
■ ®
®
-®
■
®
■
@
TOP, FRONTSIDE and BACK PANEL
0 SLUMBER - to adjust the slumber time
0DAY/REPEAT ALARM
- to switch off the alarm for a 9 minute
period
- to set the day for weekend sleeper
activation
@ 24 HR RESET - to stop the active alarm for
24 hours
0 PUSH*OPEN - to open/close the CD door
® TRACK SELECT - to select/review TRACK
SELECT number for ALM 1 or 2
® DISPUY - to show the clock/alarm times
and status of the set
® PLAY ► - to start CD playback
®BOFF
- to stop CD/Radio/Slumber function
- to cancel the TRACK SELECT setting
- to cancel alarm setting(s)
® DBB - for an enhanced dynamic bass boost
@ ALM 2 - to set/review/switch off ALM 2
@ BRIGHTNESS - to change the brightness of
the display illumination
@ALM1 - to set/review/switch off ALM 1
@ r« / ►►!
- to adjust clock/alarm times:
- to set the day
- to skip CD tracks/search tor a particular
passage
- to set a CD track for ALM 1 or ALM 2 in
TRACK SELECT mode
- to select the buzzer melody for ALM 1 or
ALM 2
@ WEEKEND SLEEPER - to deactivate ALM1
or ALM 2 for the weekend
(j|) TIME - to set the dock time
(g) BUZZER - to select the buzzer mode for
ALM 1 or 2 - to select the buzzer melody
@ RADIO ON
- to switch on the radio
- to select radio mode for ALM 1 or ALM 2
@ BAND - to select FM/MW (LW) waveband
@ 0 - 3 . 5 mm sockeyor plugging in
headphones/active speakers
@ VOLUME - to adjust the sound level
@ TUNING - to tune to radio stations
@ BaHery door - for backup batteries
@ Pigtail antenna - antenna to improve EM
reception
(g) AC MAINS - socket for AC mains lead
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved moulded 13 Amp plug. To change a fuse in this type of plug proceed as
follows:
• Remove fuse cover and fuse.
• Fix new fuse which should be a BS1362 5 Amp, A.S.TA. or BSI a^iroved type.
• Ref it the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its
place.
If the mains plug contains a fuse, this should have a value of 5 Amp. It a plug without a fuse is used, the fuse at
the distribution board should not be greater than 5 Amp.
Note: The severed plug must be disposed to avoid a passible shock hazard should it be inserted into a 13 Amp
socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral (N|, brown = live (L|.
As these colours may not correspond with the colour markings idaitifying the terminals in your plug, proceed as
follows:
• Connect the blue wire to the terminal marked N or coloured black.
• Connect the brown wire to the terminal marked L or coloured red.
• Do not connect either wire to the earth terminal in the plug, marked E (or +1 or coloured green (or green and
yellowj.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not
simply over the two wires.Copyright in the U.K.: Recording and playback of material may require consent. See
Copyright Act 1956 and The Performer's Protection Acts 1958 to 1972.
О о
m
О
H
о
Z
(Л
>
Z
D
О
О
Z
H
та
О
г~
(Л