Kenton USB-Solo - Manual (Page 19)

19
Address Function Range Notes ( see end )
00
Receive chan 0 - 15 { 1 }
01 trig / retrig 0 - 25
01 note priority 0 - 2
03 pitchbend range 0 - 24
04 portamento cont # 253 - 0 - 119 { 3 }
05 portamento time / rate 0 - 127
06 portamento type 0 – 1 0=fixed rate / 1= fixed time
07 LFO to CV depth controller # 252 - 0 - 119 { 4 }
08 LFO to CV min val 0 - 127
09 LFO to CV max val 0 - 127
10 LFO to CV reset val 0 - 127
11 coarse tune / transpose 232 > 0 > 24 { 2 }
12 fine tune val 129 > 0 > 127 129>0 = -ve
13 scale val 129 > 0 > 127 129>0 = -ve
14 v/o or hzv or 1.2v select 0 - 2
15 gate select 0 - 4
16
Aux1 Cont # 251 > 0 > 119 { 6 }
17 Aux1 min val 0 - 127
18 Aux1 max val 0 - 127
19 Aux1 reset val 0 - 127
20 Key scale to Aux 0 - 127
21 LFO to Aux1 cont # 252 - 0 - 119 { 4 }
22 LFO to Aux1 min val 0 - 127
23 LFO to Aux1 max val 0 - 127
24 LFO to Aux1 reset value 0 - 127
25
Lfo speed 0 - 191
26 Lfo waveshape 0 - 8 { 7 }
27 Lfo MIDI sync 0 - 96 { 8 }
28 Lfo sync start point 0 - 255
29 Key-on resets LFO wave 0 - 1 { 10 }
30
cont = start 0 - 1 { 11 }
31 clock divide 0 - 24 { 9 }
32 Aux 2 controller # 252 > 0 > 119 { 6 }
33 Aux 2 threshold 1 – 127
34 Aux 3 controller # 252 > 0 > 119 { 6 }
35 Aux 3 threshold 1 - 127
{ NOTES }
{ 1 } Data 0 - 15 corresponds to MIDI channels 1 - 16
{ 2 } 232 = -24 semitones 0 = no transpose 24 = + 24 semitones - 25 to 231 are invalid
{ 3 } 253=pmt off 254=pmt on 255=auto pmt & 0 - 119
{ 4 } 252=ignore 253=pitchbend 254=velocity 255=aftertouch & 0 - 119
{ 5 } 0= -64 64=0 127=+63
{ 6 } 251=trig 252=ignore 253=p.bend 254=vel 255=aft & 0 - 119
{ 7 } 0= triangle 1= saw up 2= saw down 3= 10% pulse etc. as display
{ 8 } 1 - 96 corresponds to sync divide 1 to 96 and 0 = off
{ 9 } 0 - 23 corresponds to arpeggio divide 1 to 24
{ 10 } 0=off 1=on
{ 11 } 0 = continue ignored 1 = continue=start
All sysex addresses and data are range checked and out-of-range values
will either be ignored or adjusted to give a valid response.