SINGER 148-5 - Manual (Page 9)

N O . P L A T E N A M E
4G5c 9140 Throad (under) Takc-ui> Knife So) Screw
405c 9140
“ “ “ Set Screw...........
128838 9148 “ “ “ Stripper..............
128098 9148 “ “ “ “ Bracket
1304c 9117
Screw........................................................
330 d 9118 Thread (under) Take-up Stripper Screw
128081 9131
Washer......................................................
128249 9148 Thread (under) Take-up d'hread Guard
with 220 n...................................................
128297 9149 Thread (under) Take-u{) Thread Guard
Bracket......................................................
1364c 9117 Thread (under) Take-up Thread Guard
Bracket Screw...........................................
1137 e 9118 Thread (under) Take-up Tliread Guard
Hinge Screw.............................................
128101 9148 Thread (under) Take-up Tliread Guard
Spring.......................................................
335i) 9118 Idircad (under) Take-up Thread Guard
Spring Screw............................................
220 d 9117 Thread (under) Take-up d’hread Guard
Stop Screw................................................
128100 9149 Tliread (ujiper) Controller..................................
125504 9149
“ “ “ Lever with
50138F......................................................
54879 9143 Thread (upper) Controller Lever tkm-
nection......................................................
999 f 9117 Thread (upiier) Controller Lever Con­
nection Hinge Screw (lower)...................
999 f 9117 Thread (upper) Controller Lever Con­
nection Hinge Screw (upper)...................
1700 e 9118 Thread (u|iper) Controller Lever (Con­
nection Hinge Screw (ipiper) Nut. . . .
125506 9149 Thread (upper) Controller Lever Hinge
Stud...........................................................
465c 9146 Thread (upper) Controller Lever Hinge
Stud Set Screw..........................................
125567 9149 Thread (upper) Controller Lover Post
with 465c..................................................
443c 9118 Thread (upirer) Controller Lever Post
Set Screw..................................................
50138 f 9149 'Phread (upper) Controller S(\t Screw. . .
128107 9149 “ “ “ Thread Guide
128108 9149
Po.st...........................................................
18 TARTS FÜR MACHINI': No. 148-5
N O . P J . A T B N A M E
175 f 9102 Thread (upper) Controller Thread Guide
Post Set Screw..........................................
226i) 9117 Thread (u])])er) Controller 3'hri'ad Guide
Screw.........................................................
128109 9149 Thread (ujiper) (dieek Spring (left)
2127 9149
Adjusting Plate..........................................
220n 9117 Thread (ujrper) Check S|>ring (left) Ad­
justing Plate Screw...................................
128110 9149 d'hread (upper) (.¡heck Spring (right)
128111 9149
Adjusting Plate..........................................
226 d 9117 Thread (ujrpcr) (¡heck Sirring (right)
Adjusting Plate Screw..............................
128112 9101 Thread (upper) Check Spring Regulating
Stud...........................................................
447c 9118 'Phread (upper) (¡Inrck Spring Regulating
Stud Set Screw..........................................
125568 9101 'Phread (upper) 'Pake-up...................................
217 d 9117 “ “ “ Screw..............
128300 9149 “ “ “ Stripper (left , 1 .
128301 9149 “ “ “ “ (righf)
N ote : When ordering No. 128301 state
gauge reiphred.
128114 9101 'Phread (upper) 'Pake-upStripper Bracket
14920 9117
Screw.........................................................
220o 9117 'Phread (upper) 'Pake-up Strip|>er Screw
128302 9144 Throat Plate with 128303, 128304 and
two 229i), for } / s hr. gauge, for 128278
128359 9144 Throat Plato with 128303, 128304 and
two 229u, -Д in. gauge, for 128278.. . .
128360 9144 'Phroat Plate with 128303, 128304 and
two 229i), for 3 . 4 ) in. gauge, for 128278
128)103 9144 'Phroat Plate Guide (left)...................................
128304 9144
“ “ “ (right).........................
229 d 9117 “ “ “ Screw.........................
1319 f 9118 “ “ Screw....................................
IRON BASE
N O . C I . A ' r F . N A M E
128110 9119 Machine Base with 304c, 3(l7c, 448c,
1513J, 27795, two each 935n, 42t)88,
6t)707 and three rvood screws 1 ) 2 iti.
No. 12........................................................
PARTS FOR MACHINE No. 1 tS-5 19