Maytag MAV77 - Manual (Page 7)

ШОКЕ YOU UU
For problem laundry solutions (l.e. fabric damage, residue, tangling) and special laundry care procedures, see the enclosed
Laundry Tips booklet.
CHECKTHESE POINTS IF
YOUR WASHER...
ALWAYS CHECK FIRST
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
WONT FILL
• Turn the control dial to proper cycle and
pull dial out to start the washer. If
equipped wifh buttons, be sure they are
fully depressed.
• Turn both faucets on fully.
• Straighten inlet hoses.
• Disconnect hoses and clean screens.
Hose filter screens may be plugged at the
faucet.
WONT AGITATE
• Make sure the lid is completely closed.
• Turn the control dial to proper cycle and
pull dial out to start the washer. If
equipped with buttons, be sure they are
fully depressed.
• Close lid and pull dial out to start the
washer. For your safety, washer will not
agitate or spin unless the lid is closed.
• The washer is equipped with a lid switch
failure detector. If the lid switch should
malfunction, the detector will stop opera­
tions for your safety. Call for service.
• Pauses are normal. Wait and see if the
washer will start again.
WONT SPIN OR DRAIN
• Straighten drain hoses. Eliminate kinked
hoses. If there is a drain restriction, call for
service.
• Close lid and pull dial out to start the wash­
er. For your safety, washer will not agitate
or spin unless the lid is closed.
• The washer is equipped with a lid switch
failure detector. If the lid switch should
malfunction, the detector will stop opera­
tions for your safety. Call for service.
• If drain height is over five feet, a
high-volume pump kit may be neces­
sary. See installation instructions or
call 1-800-688-9900.
LOAD IS WETTER THAN NORMAL
AT THE END OF THE CYCLE
• The washer is designed to reduce
spin speed if an unbalanced load is
detected. This is normal.
• Redistribute the load in the tub and
set the washer on SPIN.
STOPS
• Turn the control dial to proper cycle
and pull dial out to start the washer. If
equipped with buttons, be sure they
are fully depressed.
• Close lid and pull dial out to start the
washer. For your safety, washer will
not agitate or spin unless lid is closed.
• This may be a pause or soak period
in the cycle. Wait briefly and it may
start.
,
• The washer is equipped with a lid
switch failure detector. If the lid switch
should malfunction, the detector will
stop fill operations for your safety. Call
for service.
LEAKS WATER
• Make sure water inlet hose connec­
tions are tight at faucet and water
valve.
• Make sure end of drain hose is cor­
rectly inserted and secured to drain
facility.
• Avoid extended soaking - soak for
30 minutes or less.
• Avoid overloading.
IS NOISY
• Be sure washer is leveled properly
as outlined in installation manual.
• Weak floors can cause vibration and
walking.
• Be sure rubber feet are installed on
leveling legs.
• A clicking sound may be the
LoadSensor™ agitator as it moves
the load down through the cleaning
zone for maximum cleaning effectiv-
ness. This sound will vary from load
to load. This is normal.
• Operating sounds will vary depending
on agitation speed.
FILLS WITH THE WRONG TEMP­
ERATURE WATER
• Turn both faucets on fully.
• Make sure temperature selection is
correct.
• If Auto Temperature Control is select­
ed, cold water may feel warmer than
cold water from the tap (see page 3).
• Make sure hoses are connected to
correct faucets and inlet connections.
Be sure water supply is regulated cor­
rectly. Flush water line before filling
washer.
• Check the water heater. It should be
set to deliver a minimum 120T (49°C)
hot water at the tap. Also check water
heater capacity and recovery rate.
• Disconnect hoses and clean screens.
Hose filter screens may be plugged.
CYCLE SELECTOR DIAL
VANCES THROUGH “OFF”
• Extra Rinse is selected. AD-
For further assistance contact Maytag
Appliances Sales Company,
Maytag Customer Assistance:
U.S. 1-800-688-9900 dr V
: Canada 1-800-688-2002
U.S. customers using TTY for deaf,
hearing impaired dr speech impaired,
: ; can 1-800-688-2080.