SINGER 147-25 - Manual (Page 3)

INSTRUCTIONS FOR ORDERING
ID ordering from this list, use ONLÎ the part NUMBER In the
FIRST column.
The number stamped on a Sewing Machine Part Is In every сазе
the number of the single pert only.
Every combination of parte sent out as such has Its specific
number, which, although not stamped on the parts, must be used
when ordering the combination.
Each number always indicates the SA№ PART In whatever list
it appears, or for whatever machine.
The lettei-8 after some of the numbers Indicate the style of
finish only, as follows:
A-Haixlened, Polished, Nickel Plated and Buffed
A.A-Buffed and Chromium Plated
A.B-Kardened, Polished, Buffed and Chromium Plated
A.C-Brown Baking Enamel Finish
A.D-Qray Baking Enamel Finish
A.E-Hardened, Bright Rumbled and Nickel Plated
A.F-Hardened, Bright Rumbled, Nickel Plated, Bright Rumbled and
Chromltjn Plated
B-Pollshed, Nickel Plated and Buffed
C-HaiTlened only
C.R-HardeneJ and Merllzed
D-Pollshed Only
E-Soft, Not Polished
F-Hanlened and Polished
F.J-Hardened, Polished and Nickel Plated
Q-Brlght Rumbled and Nickel Plated
H-Blued
J-Nlckel Plated Only
K-Hardened and Nickel Plated
L-Brass Plated
M-Qxldlzed
N-Japanned, Dull
P-Japannod, Bright
P.P-WrInkle Finish
R-Merllzed
S-Cadmium Plated
T-Copper Plated
T.A-Hardoned, Polished, Copper and Nickel Plated and Buffed
T.B-Copper and Nickel Plated and Polished
T.J-Copper and Nickel Plated Only
T.K-Hardened, Copper and Nickel Plated
T.L-Copper and Brass Plated
T.M-Copper Plated and Oxidized
U-Zlnc Plated
V-Sllver Plated
W-Pollshed and Nickel Plated
X-Black Oxide, for Iron and Steel
X.C-Hardened and Black Oxide, for Iron or Steel
Y-Black Nickel Plated Only
Z-Chromlum Plated
Z.A-Hardened,Polished,Nickel Plated,Buffed and Chromium Plated
Z.B-Pollshed, Nickel Plated, Buffed and Chromium Plated
Z.C-Hardened and Chromium Plated
Z.D-Pollshed and Chromium Plated
Z.Q-Brlght Rimbled, Nickel Plated, Bright Rumbled and Chromium Plated
Z.J-Nlckel and Chi'omlum Plated
Z.T-Copper and Chromium Plated
These letters MUST BE USED when they appear in the list; and
AFTER che number as in the list.
In this scries:
1 to 1500, 50001 to 51500 and 140001 to 142000
are Screw Numbers
1501 to 1800 and 51501 to 51800 are Nut Numbers
1801 to 2000 and 51801 to 52000 are Roller Numbers
2001 to 50000 and 52001 to 140000 and 142001 to
100000 are Sewing Machine Parts, 190001 and upward
are numbers of Electrical Parts.
The flgiu'ôs In the second column refer only to the plates.
Illustrating the parts, and are NOT TO BE USED In ordering.
Parts marked with an asterisk are furnished only when
repairs are inade at factory..
When oi’derlng parts which differ as to Qauge (the distance
between seams} the Gauge, as well as the Number must bo given on
order.
LIST OF PARTS COMPLETE
FOR
MACHINE No. 147-25
For Covering Seams, Necking and Ornamenting Knit Under­
wear. Two needles, one looper. Gauges Vs inch, Inch and
V 4 inch. Speed up to 3200 R. P. M. according to the material
being stitched.
No. Plate Name
*131128 Ann, , upper and lower (solid) with 948J,
15404 and two 15405...............................................................
42366 20641 Ann Oil Pad (braided cotton) for oiling
Arm Rock Shaft Front Bearing................................................
56006 20641 Arm Oil Pad (braided cotton) for oiling
Arm Rock Shaft Intermediate Bearing.
56003 20641 Arm Oil Tube with 52045, for oiling
Needle Bar Connecting Link....................................................
11119 20641 Arm Oil Tube with 52045, for oiling
Thread (upper) Nipper..............................................................
52045 20641 Arm Oil Tube Packing (wick)..........................................................
68118 20641 f t Rock Shaft.................................................................................
68119 i t " " 68118 with 54004 and 64255
64386 20641 f t " " Bushing (back)..............................................................
4460 20641 f l " “ " " Set Screw..
64388 20641 J l " " (intermediate)....
423C 20641 U « " " " Set
Screw.........................................................................................