SINGER 147-60 - Manual (Page 10)

20 PARTS FOR MACHINE No. 147-60
N O .
1449 j
P L A T E
20501
54096 —
21 I f
131033
9923
20510
131017 20511
131119 20512
131163 20513
131172 20510
131173 20511
131094 20512
131166 20513
N ote : When
742 f 20504
N A M E
Thread (upper) Take-up Plate Spring
Screw...........................................................................
'I'hread (upper) Take-u|i complete, Nos.
1449J, 54094, 54095 and 08164.............................
Thread (upper) Take-up Set Screw..............................
Throat Plate, for in. to in. gauges,
for 131032, for lap seam felling..............................
'Phroat Plate, for in. to in. gauges,
for 68472, for lap seam felling................................
Throat Plate, for in. and 'j-g in.
gauges, for 131093, for lap seam
felling...........................................................................
'Phroat Plate, for Js in. to p-j in. gauges,
for 131160, for lap seam felling..............................
'Phroat Plate, for /5 in. to in. gauges,
for 131032, for plain stitching.................................
'Phroat Plate, for in. to i*‘- gimges,
for 68472, for plain stitching...................................
'Phroat Plate,for jj in.and in. gauges,
for 131093, for plain stitching.................................
'Phroat Plate, for ;i g in. to p2 in. gauges,
for 131160, for plain stitching.................................
ordering 'Phroat Plates, state gauge
reipiired.
'Phroat Plate Screw.........................................................
SINGER Needles should be used
in SINGER Machines
These Needles and their Containers
are marked with the
Company’s Trade Mark "SIMANCO.**” 1
Needles in Containers marked
"FOR SINGER MACHINES”
are NOT SINGER made needles. 2
21
LIST OF PARTS COWPLETE
FOR
MACHINE No. 147-61
FOR LAP SEAM FELLING SHIRT SLEEVES OF LIGHT WEIGHT
MATERIALS, ALSO FOR TWO LINE STITCHING KNICKERS,
PLAY SUITS, UPHOLSTERY, SEAT COVERS, KNIT UNDER­
WEAR, BATHING SUITS, ETC.
TWO NEEDLES, TWO LOOPERS. GAUGES 3 ^, IN. TO H IN.
NEEDLE BAR STROKE INCHES. THE LOOPERS ARE
ARRANGED SO THAT THEY MAY BE THROWN OUT OF
POSITION
FOR CONVENIENCE IN THREADING. AN
IMPROVED OILING SYSTEM AUTOMATICALLY OILS ALL OF
THE PRINCIPAL BEARINGS OF THE MACHINE. BALANCE
WHEEL N0. 64259. DIAMETER OF BELT GROOVE 2 INCHES.
SPEED 4000.
. ' J O . I ' L . W E N A M E
•68127 --------- .-Lrin, U])per and lower (solid) with 918 j ,
68483 and four 131022.......................................
68128 9917 Arm Bottom Cover................................................................
68429 9917 “ “ “ Gasket (cork)............................
1057 e 20503 “ “ “ Screw........
68350 9922 “ Oil Cup, for oiling Arm Rock Shaft
Front Bearing..............................................................
68430 9922 Arm Oil Cup, for filling oil reservoir—
54618 9922 “ “ “ Oil Pad (braided cotton)
for 68350......................................................................
68431 9916 Arm Rock Shaft.....................................................................
68432 “ " “ 68431 with 1235 f and
68439............................................................................
1309c 20504 .Arm Rock Shaft .Adjusting Screw.........................................
131056 20504 " “ “ “ “ Washer
68433 9916 “ “ “ Bushing (back).....
68434 ---------------- " “ “ “ “ 68433
with 52045.................................................................
68435 9916 .Arm Rock Shaft Bushing (back) Cap
131095 9916
Washer (fibre)............................................................
52045 9922 Arm Rock Shaft Bushing (back) Oil Pad
(wick)...........................................................................
446c 20503 Ann Rock Shaft Bushing (back) Set
Screw............................................................................
68436 9916 .Arm Rock Shaft Bushing (intermediate)
68437 --------- “ " “ “ “
08136 with 52045.......................................................