Instructions for ordering, Machine no. 147-30, List of parts complete – SINGER 147-30 User Manual
Page 3
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
INSTRUCTIONS FOR ORDERING
In ordering from this list, use ONLY the part NUMBER
in the i’lRST column.
The number stamped on a Sewing Machine part is in every
case the number of the single part only.
Every combination of parts sent out as such has its specific
number, which, although not stamped on the parts, must be
used when ordering the combination.
Each number always indicates the SAME PART in whatever
list it appears, or for whatever machine.
The letters after some of the numbers indicate the style of
finish only, as follows:
A—•Hardened, Polished, Nickel Plated and Buffed
B—Polished, Nickel Plated and Buffed
C—Hardened Only
D—Polished Only
E—Soft, Not Polished
F—Hardened and Polished
H—Blued
J—Nickel Plated Only
K—Hardened and Nickel Plated
L—Brass I’lated
M—Oxidized
N—Japanned, Dull
P—Japanned, Bright
R—Merlized
T—Copper Plated
T. A.—Hardened, Polished, Copper and Nickel Plated
and Buffed.
T. B.—Copper and Nickel Plated and Polished.
T. J.—Copper and Nickel Plated Only.
T. K.—Hardened, Copper and Nickel Plated.
T. M.—Copper Plated and Oxidized.
T. J j .—Copper and Brass Plated.
U—Zinc Plated
V—Silver Plated
W—Polished and Nickel Plated
Z—Chromium Plated
Z. B.—Polished, Nickel Plated, Buffed and Chromium Plated
Z. J.—Nickel and Chromium Plated.
These letters MUST BE USED when they appear in the list;
and AFTER the number as in the list.
In this series'.
1
to 1500 and 50001 to 51500 are Screw Numbers
1501 to 1800 and 51501 to 51800 are Nut Numbera.
1801 to 2000 and 51801 to 52000 are Roller Numbers.
2001 to 50000 and 62001 and upward are numbers of
Machine Parts.
The figures in the second column refer only to the plates,
illustrating the parts, and are NOT TO BE USED in ordering.
Parts marked with an asterisk (*) are furnished only when
repairs are made at factory.
When ordering parts which differ as to
Gauge
(the distance
between seams) the Gauge, as well as the
Number must be
given
on order.
LIST OF PARTS COMPLETE
FOR
MACHINE No. 147-30
FOR GENERAL WORK IN FABRICS WHERE THREE-LINE
STITCHING IS DESIRED. THREE NEEDLES AND THREE
LOOPERS, FOR LAP SEAM FELLING. GAUGES FROM IN.
TO A IN. BETWEEN EACH NEEDLE. SPEED UP TO 3500,
ACCORDING TO THE MATERIAL BEING STITCHED.
NO.
54001
—
423()() 8901
50000
8901
5t)00:i
8985
52045
8901
54002
8902
54079
—
04380
8901
440c 8901
04388
8901
423c 8901
N.\MB
.\rm, \ipper and lower (solid) with 948»
and 540:M.......................................................
.\rm Oil Pad (braided cotton) for oiling
Arm Rock Shaft Front Bearing.......................
,\rm Oil Pad (braided cotton) for oiling
Arm Rock Shaft Intermediate Bearing.
Arm Oil Tube with 52045, for oiling 54320
"
“
“ Packing (braided cotton). ,
“ Rock Shaft.....................................................
“
•'
“
54002 with 54004, 54005
and 04255.......................................................
Arm Rock Shaft Bushing (back).........................
“
“
“
“
“ Set Screw
“
“
“
“
(intermediate)
t«
it
( (
<<
i i
Set Screw........................................................