Autostart Two-way 6-Button LCD Automatic Transmission Remote Starter User - Manual (Page 6)

The parking lights will flash once.
If remote door locks are installed, this will also lock the doors.
• In passive mode, the starter kill will automatically arm if the ignition key is not inserted
into the ignition switch within 1 or 3 minutes after unlocking (the key sense feature
must be installed).
Rernote Starter Features _ ______ _________________
Idle Mode
Convenience feature: Idle mode allows you to keep the engine running and the doors locked
while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no key in the
ignition switch) while the engine is running. For example, if you stop for a delivery or at a conveni­
ence store, lock your vehicle and leave it running for the length of a run cycle while you are away.
To leave the vehicle in idle mode:
1. With the engine running, press the S or S button (to unlock the doors) or the ^ button on
the remote control until the parking lights come on.
2. Remove the key and exit the vehicle. The engine will go on running.
3. Lock the doors if needed.
The engine will go on running until the user re-enters the vehicle or until the expiration of the
engine run time.____________________________________________________________________
CautioniH Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Valet Modes
Ignition Valet
This feature will allow you to remotely put your system into valet mode by using the ignition key
instead of the valet button as above. Ignition valet can be used without a valet button installed.
To put the system i n t o valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times successively into
the IGNITION ON; run and o ff positions.
The parking lights will flash three times to indicate that the vehicle is now in valet mode. The L.E.D.
will come
ON solid.
— The El icon will appear on your LCD remote.
To take the system out of valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times successively into
the IGNITION ON; run and o ff positions.
The parking lights will flash twice to indicate that the vehicle is now out of valet mode. The L.E.D.
will go out.
— The
El
icon will disappear from your LCD remote.
Note: With the Ignition valet activated, the remote starter will be disabled.
Remote Valet Mode
This feature will allow you to remotely put your system into valet mode by using the transmitter
instead of the valet button as above.
Getting into vaiet mode
• Hold the Hand ^ buttons simultaneously for 3 second.
• The parking lights will flash 3 times.
The LED will remain on solid.
— The Eicon will appear on your LCD remote.
Getting out of vaiet mode •
• Hold the Hand ^ buttons simultaneously for 3 second.
• The parking lights will flash 2 times.
The LED will turn off.
P. 6 User Guide
Note: to change the temperature from Celsius to Fahrenheit, press IE] + |i+ ^ simultaneously.
Horn Chirp Timing
The pulse duration can be configured by your installer (from 5 ms to 200 ms).
Flashing LED
The user may decide to turn on or off LED flashing at any moment. To do so, simultaneously press
and hold the
S
and
H
buttons on the transmitter or press and hold the button. There will be
an initial beep. Keep holding the buttons pressed until you hear another beep. At that point
release the buttons. The parking lights will flash once if the LED is turned on or three times if the
LED is turned off.
There are three programmable options regarding the flashing LED:
i. The LED flashes once the starter kill is activated (passive or active arming) and will
turn itself off once the user turns the key to the
ignition o n position.
ii. The LED is totally disabled and will not flash -it will turn on solid, however, when in
valet mode.
III. The LED will flash once the starter kill is activated but requires pressing the IB
button to turn itself off. Failure to press the
H
button will make the LED flash even
if the key is in the ignition o n position.
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same remote starter model, to
control both systems with a single remote control. To control the second vehicle:
Note: Your remote control must be configured for second car operation by the installer.
Press Ii + ^Simultaneously:
Press Ii + ^Simultaneously:
Press ^simultaneously:.
Press li+ ^
Press
JE1>
simultaneously:.
........
. LOCK
.UNLOCK
..START
. STOP
.TRUNK
or
Press
JE1> JE1>
H:..............................................
Press [E]> H:...........................................................
Press
El> El> ^:.........................
Press [E]> ^:............................................................
Press
JE1> JE1> Ii:
........................................................................ TRUNK
Note: In order to access the 2 nd car operations with the companion remote, Shift button must be
pressed twice quickly and then one more time followed by lo ck , unlo ck , trunk or start / stop .
. LOCK
.UNLOCK
..START
. STOP
LCD Transmitter Operation and Confirmations (Second Car Control)
Basic Operations
Function Button press Icon Sound Description
Lock
n
o
1 beep
User Guide P. 11