Learning - advanced – Konig Electronic 8:1 universal remote control User Manual
Page 17
17
Note
:
For audio equipment, fi rst press the Shift button (
shift
) and then the
TV/CD button (
tv
/
cd
) for CD,
STB/TAPE button (
stb
/
tape
) for TAPE,
DVD/TUNER button (
dvd
/
tuner
) for TUNER or
AUX/AMP button (
aux
/
amp
) for AMP
2)
Enter the code 0 0 0 9 using the numeric buttons. The signal LED fl ashes twice again.
3)
Now, the signal LED lights up in green.
4)
Press the button on the KN-URC80B remote control that you would like to teach, e.g., standby ( )
5) The signal LED lights up in orange and indicates that the KN-URC80B remote control is ready to learn.
6) Press and hold the desired button on the original remote control until the green signal LED goes off.
Note
:
Orange light indicates that the KN-URC80B is not receiving any signal.
If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).
7)
You may repeat the steps 3 to 6 to teach (or programme) other buttons. To save and end the learning function,
press the TV (
tv
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button that had been pressed earlier.
Note
:
If the buttons that have been learnt do not work properly with your equipment, or particularly if only every second
button that you press works, please carry out Advanced Learning.
Learning - Advanced
1)
Press and hold the TV (
tv
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button depending on the level that you wish to
programme until the signal LED (
) fl ashes twice.
Note
:
For audio equipment, fi rst press the Shift button (
shift
) and then the
TV/CD button (
tv
/
cd
) for CD,
STB/TAPE button (
stb
/
tape
) for TAPE,
DVD/TUNER button (
dvd
/
tuner
) for TUNER or
AUX/AMP button (
aux
/
amp
) for AMP
2)
Enter the code 0 0 1 0 using the numeric buttons. The signal LED fl ashes twice again.
3)
Now, the signal LED lights up in green.
4)
Press the button on the KN-URC80B remote control that you would like to teach, e.g., standby ( )
5)
The signal LED lights up in orange and indicates that the KN-URC80B remote control is ready to learn.
6)
Press and hold the desired button on the original remote control until the green signal LED goes off.
Note
:
Orange light indicates that the KN-URC80B is not receiving any signal.
If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).
7)
Press and hold the same button on the original remote control once again until the green signal LED goes off.
8)
You may repeat the steps 3 to 7 to teach (or programme) other buttons. To save and end the learning function,
press the TV (
tv
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button that had been pressed earlier.
Operating the volume control on the TV or satellite receiver or the DVB-T / cable box
(STB) or DVD player / recorder
By default, the volume and mute controls are operated on the satellite receiver or DVB-T / cable box or DVD
player / recorder.
If you would like to operate these controls on the TV, please carry out the following steps.
1)
Press and hold the TV button (
tv
), until the signal LED (
) fl ashes twice.
2)
Enter the code 0 0 0 4 using the numeric buttons. The signal LED fl ashes twice again.
If you would like to restore the volume control functions again to the satellite receiver or the DVB-T / cable box
(STB) or the DVD player / recorder, please carry out the following steps.
1)
Press and hold the TV button (
tv
) until the signal LED (
) fl ashes twice.
2)
Enter the code 0 0 0 5 using the numeric buttons. The signal LED fl ashes twice again.
BA König KN-URC80B, 135x215 mm CS6.indd 17
BA König KN-URC80B, 135x215 mm CS6.indd 17
12.09.2012 10:56:16
12.09.2012 10:56:16