Q&Q QUARTZ L104J - Manual (Page 2)

Timer Mode
● This Watch includes two timers, they are Timer 1 and Timer
2.
● Press [L/R] button to select the display between Timer 1
and Timer 2.
Counting Mode
● There are 3 counting modes for Timer 1 and Timer 2:
● 'Countdown Stop' - CS : The timer starts the counting
from a target time to zero and then stops at zero.
● 'Countdown Repeat' - CR: The timer starts the counting
from a target time to zero and then starts the counting
again and again whenever it counts to zero.
● 'Countdown Linkage' - LK: The timer (e.g Timer 1) starts
the counting from the target time (Timer 1) to zero and
then starts the counting from another target time (Timer
2) to zero, and vice versa.
● Check the coming chapter for the detail of how to set the
target time and the counting mode for a timer.
Pacer Mode
● This Watch includes a pacer which will generate beeps at a
preset beeping rate.
● The beeping rate can be set from 30 to 240 beats per minute
(bpm).
How to Use the Pacer
● Set a beeping rate (e.g 30 bpm) for the Pacer before using
the pacer.
● Press [S/S] to start or stop the pacer.
● When the pacer is started, it starts beeping at the preset
beeping rate with a flashing 'P' indicator.
How to use Pacer with the Chronograph
● This Watch includes a function which allows the pacer
working with the chronograph.
● To use the pacer with the chronograph, press [M] to select
the Chronograph Mode when the Pacer is ON.
● When Chronograph Mode is selected, press [S/S] to start or
stop the Chronograph with the Pacer (beeps) at the same
time.
Current Time Mode
● Time System: AM, PM, Hour, minute, second.
● Time Format: 12-hour or 24-hour format.
● Calendar: Month, date and day of week display
(Auto-Calendar).
Alarm Mode
● Two daily alarms.
● Alarm sound: 30 seconds.
● Hourly chime.
Chronograph Mode
● Resolution: 1/100 second.
● Measuring Range: 23 hours 59 minutes, 59.99 seconds.
● Lap memory: Maximum 100 lap memories (see below
note); Maximum 30 segments.
NOTE: As registered a segment consumes memory,
thus the effective number of laps will be reduced as
number of segment increases.
● Date Stamp: Auto registered the starting time and date
for the 1st. lap each of segment.
Timer Mode
● Resolution: 1 second.
● Measuring Range: 23 hours 59 minutes, 59 seconds.
● Counting Mode: 3 modes (Countdown-stop;
countdow-repeat; countdown-linkage).
● Timer Sounds: beep once at last 5,4,3,2,1
second(s). Beep for about 10 seconds when reach
zero.
Pacer Mode
● Setting Range: 30 bpm to 240 bpm.
● Setting step: 5 bpm.
Dual Time Mode
● Time System: AM, PM, Hour, minute, second.
Back Light (For Watch Model Only)
● Back Light Type: Electro-Luminescent (EL) back light.
How to Use the Timer
● Once the target time has been set (e.g: 10 minutes), press
[S/S] to start or stop the counting.
● The counting time will be exhibited on the 3rd. row of display
throughout the measurement.
How to Reload the Timer
● Hold the [L/R] to reload the target time when the timer has
been stopped.
Timer Alarm Sound
● The Watch will beep once when it comes to the last 5,4,3,2,1
second(s).
● The Watch will beep for about 10 seconds when it reaches
zero.
● When the Watch is beeping, press any button to stop the
beep prematurely.
Dual Time Mode
● This Watch includes a dual time which provides
the supplementary timekeeping function to
another time zone.
6.1 Chronograph Recall Mode - Delete the Lap Memory
7.0 Timer Mode
- About the Timer Mode
7.1 Timer Mode - Setting the Timer
7.2 Timer Mode - Using the Timer
8.0 Dual Time Mode - Dual Time Mode
8.1 Dual Time Mode - Setting the Dual Time
9.0 Pacer Mode
- Pacer Display
9.1 Pacer Mode - Setting the Pacer
9.2 Pacer Mode
- Using Pacer with the Chronograph
10.0 Specifications
NOTE:
● The segement number will be forward shifted if one particular
segment has been deleted. For example, if three segments
have been saved, the former segment 3 will become the
segment 2 when the former segment 2 has been deleted.
● A segment cannot be deleted (A 'FAIL' message will be
appeared) if it has not been saved into memory, i.e. the
chronograph is still counting on that segment.
NOTE:
● The setting display can only be selected if the pacer is stopped.
● Press
[L/R] to move the selection in the reverse direction.
● Hold down the button to move the selection at a faster rate.
● The Watch/Stopwatch returns to Pacer Mode if NO key has been
operated for about 1 minute.