Weston Cuber/Tenderizer & Jerky Slicer Motor - Manual (Page 4)

ASSEMBLY INSTRUCTIONS
1. Set up the manual cuber/jerky slicer per the instructions that came with the unit.
2 Remove the handle from the manual cuber/jerky slicer and set it aside. The handle
will not be used when the motor is attached.
3. Using the provided Allen Wrench, remove the two
socket head screws from the handle side of the
manual cuber/jerky slicer.
Figure 1
4. Position the Motor Bracket so that the holes in the
bracket line up with the holes on the handle side of
the cuber/jerky slicer. Figure 2
5. Install the two provided 16mm Allen Head Bolts
through the Motor Bracket and into the cuber/jerky
slicer housing. Be sure the bolts are firmly tightened.
Figure 3
6. Screw the Adapter into the cuber/jerky slicer. Figure 4
7. Insert the Motor Shaft fully into the Adapter, allowing
the Motor to rest on the Motor Bracket. Figure 5
Note: The Motor Shaft may need to be rotated for
proper alignment.
8. Slide the two 110mm Hex Head Bolts through the
holes in the Bracket. Figure 6
Note: The threaded ends of the bolts should be
facing the Motor.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Socket
Head
Screws
Motor
Bracket
16mm
Allen Head
Bolts
Adapter
Adapter
Motor
Shaft
110mm
Hex Head
Bolts
1. ALWAYS DISCONNECT product from
power source before servicing or cleaning the
unit.
2. KEEP FINGERS CLEAR of the cutting
blades at all times. Failure to keep fingers
clear of the cutting blades may result in
personal injury.
3. NEVER REACH INTO the top opening,
doing so could cause serious injury. Always
use the provided tongs.
4. KEEP CHILDREN AWAY. NEVER
LEAVE THE UNIT UNATTENDED. Be safe,
DISCONNECT from power source before
leaving the work area.
5. REDUCE RISK OF UNINTENTIONAL
STARTING. Make sure the power switch is
in the “OFF” position before attaching to the
power source. In the event of a power failure,
move the switch to the “OFF” position.
6. CHECK FOR DAMAGED PARTS. Before
using the Motor, check that all parts are
operating properly, and perform the intended
functions. Check for alignment of moving
parts, binding of moving parts, mounting
and any other conditions that may affect the
operation.
7. DO NOT USE the Motor if the power
cord is damaged. It MUST be replaced
before using the motor. Do not modify
the cord provided. DO NOT allow the
power cord to drape into your work area.
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT: FAILURE TO
COMPLY WITH PROCEDURES AND SAFE GUARDS
MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE.
REMEMBER: YOUR PERSONAL
SAFETY IS YOUR RESPONSIBILITY!
8. FOLLOW THE MANUFACTURERS
SAFETY INSTRUCTIONS on the cuber/jerky
slicer and the Motor.
9. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Motor.
REMOVE ties, rings, watches, bracelets, or
other jewelry before operating the Motor.
10. WEAR EYE PROTECTION. Wear safety
glasses. Everyday eye glasses are not safety
glasses. Safety glasses conform to ANSI
Z87.1 requirements. Note: approved safety
glasses have Z87 printed or stamped on
them.
11. Do not use the Motor while under the
influence of drugs, alcohol or medications.
12. Do not overreach, keep proper footing and
balance at all times.
13. DO NOT FORCE THE UNIT. The cuber/
jerky slicer will do the job better and is safer at
the rate for which it was designed.
14. STAY ALERT! Watch what you are doing.
A moment of inattention while operating the
unit may result in serious personal injury.
WARNING!
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
-5- -4-