Weston Harvest Guar Portable Vacuum Sealer User Manual

Page 9

Advertising
background image

-9-

-16-

stop automatically and “BEEP” when the vacuum and seal processes are complete.

There are a series of seven lights on the bottom right corner of the

Control Panel (Figure

6) that indicate the

VACUUM/SEAL PROGRESS.

Press the

ON/OFF Button to stop the vacuum process at any point.

9. DO NOT try to open the

Vacuum Lid before the vacuum has released or damage

may occur. Press both of the

Lid Release Buttons (Figure 7) on each side of the

Vacuum Sealer to release the lid lock, then lift the Vacuum Lid to open.

10. Remove the vacuum sealed bag. Wait at least 20 seconds before sealing another bag

to avoid overheating the unit.

11. Press the

ON/OFF Button (Figure 6) on the Control Panel to turn the Vacuum

Sealer “OFF”.
11. Disconnect the

Vacuum Sealer from the power supply before leaving the work area

and when work is complete.

REPLACING THE SEAL BAR TAPE:

1. Press the

ON/OFF Button on the

Control Panel to turn the Vacuum Sealer

“OFF”.

2. Disconnect the

Vacuum Sealer from the

power supply.

3. Make sure the

Vacuum Sealer is

completely cool.

4. Pick at either end of the

Seal Bar

Tape covering the Seal Bar Heating

Element until it lifts slightly (Figure 18).

Grasp the loose end and slowly pull

the

Seal Bar Tape back over itself until fully

removed.

5. Remove the backing from a new strip of

Seal Bar Tape. Be careful not to allow the

Seal Bar Tape to contact anything including itself while the adhesive side is exposed.
6. Hold one end of the

Seal Bar Tape in each hand. Stick the left end of the Seal Bar

Tape to the flat area on the Base just left of the Seal Bar Heating Element. Apply the

Seal Bar Tape from left to right over the Seal Bar Heating Element. Make sure there

are no wrinkles or folds in the

Seal Bar Tape once applied. The Seal Bar Tape should

fully cover the

Seal Bar Heating Element.

Figure 18

Seal Bar Tape

Seal Bar Heating

Element

6. Remove the

Plastic Lid Base, 2

Release Buttons and the 2 Release

Springs from the Stainless Steel Lid.
7. To install the new

Lid Assembly, turn

the

Plastic Lid Base upside down with the

Vacuum Chamber Lid Seal positioned

towards the front of the

Vacuum Sealer

and the

Seal Bar Insulator facing you.

8. Place the 2

Release Buttons into the

slots (Figure 20). Insert the 2

Release

Springs into the backs of the Release

Buttons.
9. With the

Vacuum Chamber Lid

Seal positioned towards the front of

the

Vacuum Sealer and the Seal Bar

Insulator facing you, carefully position

the

Plastic Lid Base Assembly back

onto the

Stainless Steel Lid so that the

4 screw holes in the

Plastic Lid Base

line up with the 4 screw posts on the

Stainless Steel Lid.
10. Use one hand to hold the

Plastic Lid Base and the other to insert and turn the 4 Lid

Screws. HINT: It may work better to tilt the Vacuum Sealer on its side when installing

the

Lid Screws.

11.When all 4

Lid Screws are installed, the Plastic Lid Base should be flush to the

Stainless Steel Lid. If it is not, then the Lid Screws may be improperly installed (i.e.

crooked or not tight enough).

Release Button

Figure 20

Release Spring

Plastic Lid Base

Stainless Steel Lid

Seal Bar Insulator

Screw

Posts

NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For

best results, only use the recommended vacuum bags with an embossed or mesh lining.

DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other

than the uses described in this booklet, could potentially damage the appliance and void

the warranty!

Advertising
This manual is related to the following products: