Woodhaven 8250K: Portable Router Table, Fence & Leg Set - Manual

8250K
Portable Router Table
Owners Manual
Please Read Carefully!
8250K Parts List
The 8250K consists of the PTM100 Router Table, 363
Leg Set and 201 Router Fence. See their respective
Parts List for their individual components.
PTM100 Router Table Parts List:
Part Description Quantity
PTM100T Table, 15-5/8” x 23-3/4”. . . . . . . . . . . . . . . . . . . . . . . . . 1
PTM100P Router Plate w/mounting instructions . . . . . . . . . . . 1
101A
Starting Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MF015 1/4-20 x 1” flathead screw . . . . . . . . . . . . . . . . . . . . . . 4
NUT010 locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
WFN002 1” washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
363 Leg Set Parts List:
Part Description Quantity
363B Leg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
HB040 1/4-20 x 1-1/4” bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WS002 washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WL001 lock washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5792B 1/4-20 x 3/4” barrel nut . . . . . . . . . . . . . . . . . . . . . . . 12
CAB035 non-skid foot pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
BEFORE BEGINNING
Identify and verify that you have all the parts
listed. Read the instructions at least once, familiarizing
yourself with the parts, before beginning. You’ll need a #3
Phillips screwdriver and a 7/16" socket for assembly.
ATTACH 363 LEG SET TO TABLE
Get the parts for the Leg Set (363). Place a lock washer
(WL001) and then a washer (WS002) on the eight 1-1/4"
bolts (HB040). Get the Table (PTM100T), set it upside down
on a bench and let one corner hang over the edge, enough
to access the two mounting holes for a Leg (363B). Insert
two 3/4" barrel nuts (5792B) in the holes near the wide end
of the Leg, aligning the hole in the barrel nut with the cross
hole in the Leg. Set the wide end of the Leg on the underside
of the Table, aligning the mounting holes with each other.
Insert a bolt up thru each Table mounting hole, screwing it
into the barrel nut by hand. Tighten both bolts with a 7/16"
socket. Repeat for the remaining three legs. See fig. 1A.
Insert a 3/4" barrel nut in the hole in the narrow end
of the Leg, aligning the hole in the barrel nut with the cross
hole in the Leg. Screw a non-skid foot pad (CAB035) into
the barrel nut until tight. See fig. 1B.
1
A
5792B &
CAB035
5792B, WS002,
WL001 & HB040 x2
PTM100T
363B
B