Desa VML27NR - Manual (Page 16)

111115-01D
16
For more information, visit www.desatech.com For more information, visit www.desatech.com
ON
OFF
REMOTE O FF
PILO T
O
N
L O
I H
Selector Switch in REMOTE Position
(Optional Hand-Held Remote Control)
Control Knob in
On Position
Flame Adjustment
Knob
Piezo Ignitor
OPERATING HEATER
Continued
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1. Remove control cover log (see Figure 28, page 15).
2. Turn control knob clockwise to the OFF position.
3. If Using Optional Hand-Held Remote: Let unit cool. Remove
all logs from base and set remote sensor selector switch to
the OFF position.
4. Replace control cover log (or all logs if removed in step 3).
See Installing Logs, pages 13 and 14.
Shutting Off Burner Only (pilot stays lit)
You may shut off the burner and keep the pilot lit by doing one
of the following:
1. Remove control cover log (see Figure 28, page 15). Turn
control knob clockwise
to the PILOT position. Re-
place control cover log.
2. If Using Optional Hand-Held Remote: Use remote control
manual OFF button.
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 6 under Lighting Instructions, page 15.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow
steps 9 through 11, page 15.
OPERATING HEATER
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Hand-Held Remote Operation
WARNING: Make sure remote sensor selector
switch is in the OFF position when you are away from
home for long periods of time. Follow step 3 under
Shutting Off Heater.
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 27). Follow instructions included
with the remote control.
OPTIONAL HAND-HELD
REMOTE OPERATION
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions on page 15.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position (see Figure 52).
Note: The burner
may light if hand-held remote was on when selector switch
was last turned off. You can now turn the burner on and off
with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the RE-
MOTE or ON position when the pilot is not lit. This will
drain the battery.
Figure 31- Setting the Selector Switch, Control Knob, and Flame
Adjustment Knob for Hand-Held Remote Operation
Figure 32 - On/Off Hand-Held Remote Control Unit (GHRCB)
Control Button
Turns Burners
On and Off
ON/OFF SERIES (MODEL GHRCB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 32).
TO LOCK press both buttons on hand-held remote control until
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
TO UNLOCK press both buttons together on hand-held remote
control until the light stops flashing. The hand-held remote is
now unlocked.
THERMOSTAT SERIES (MODEL GHRCTB)
The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 33).
To select Fahrenheit/Centigrade mode display, carefully press
the ˚C/˚F mode button with the end of a paper clip or similar
blunt object.