Denon CDR-W1500 - Manual (Page 9)

ENGLISH
9
r
Input source display
• Each press of the input switching button (INPUT)
causes the indicators to light as described below.
CD : This lights when the input source is set
to the internal CD.
OPT : This lights when the DIGITAL IN
OPTICAL input jacks are selected.
COAX : This lights when the DIGITAL IN
COAXIAL input jacks are selected.
ANALOG : This lights when the ANALOG CD-R IN
input jacks are selected.
ª
ª
ª
ª
t
Music calendar display
• Tracks on a disc or in a program.
• Track in play/recording.
✽ Off when both the CD and CD-R times are displayed.
y
Multiple display
• This display indicates the number of tracks, track
number, play time, recording time, various operational
information, text messages, etc.
• When both the CD and CD-R times are displayed, the
CD-R time is displayed.
u
Level meter
• Record level bar, indicates the audio signal level.
• When the CD-R unit is set to the recording mode, the
input level is displayed.
i
Track No. display
• When there is text information, the track number is
displayed.
• When both the CD and CD-R times are displayed, the
CD track number is displayed.
o
Time display
• When there is text information, the time is displayed.
• When both the CD and CD-R times are displayed, the
CD time is displayed.
8 REMOTE CONTROL UNIT
2 The included remote control unit (RC-278) can be used to operate the CDR-W1500 from a distance.
q Remove the remote control unit’s back lid.
w Insert the two R6P (AA) batteries in the battery
compartment, in the direction indicated by the marks inside
the compartment.
e Put the back lid back on.
Cautions on batteries
• Use R6P (AA) batteries in the remote control unit.
• The batteries should be replaced with new ones after
approximately one year, though this depends on the
frequency with which the remote control unit is used.
• Even if the batteries are less than a year old, replace
them with new ones if the remote control unit no
longer operates even from a short distance from the
main unit.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting new batteries, wait about two
minutes after removing the old batteries before
inserting the new ones.
• Be sure to set the batteries in the proper “<” and
“>” directions, as indicated by the marks in the
remote control unit’s battery compartment.
• Remove the batteries when not using the remote
control unit for long periods of time.
• To avoid explosions and fluid leakage:
• Do not use one new battery with one old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose
of batteries in flames.
• If the battery fluid should leak, wipe all the fluid off
the battery compartment, then insert new batteries.
• When operating the remote control unit, point it at
the main unit as shown in the diagram.
• The remote control unit can be operated from a
direct distance of approximately 8 meters from
the main unit. This distance will be shortened,
however, if there are obstacles or when operated
from an angle.
(The remote control unit will operate from a
horizontal angle of up to about 30°.)
TIM E CL EA R INP UT
ME NU
OP EN /C LO SE
PH ON ES LE VE L
FIN AL IZE
8 9
PL AY
ST OP PA US E 4 RE C
-
30°
30°
ST OP
PA US E PL AY
2
4
3
7 8 5 6 1 9
10 +10 RE C
_ DU BB IN G _ NO RM AL HI GH RE LA Y MO DE CD CD -R
EN TE R ME NU
8
9 3
2
6
7
PR OG /DI RE CT CA LL
RA ND OM DIS PLA Y S EL. FA DE R IN PU T FIN AL IZE 1 / A LL A - B CH AR AC TE R
TI ME TI TL E
B RE MO TE C ON TR OL U NI T RC -2 78
M M CL EA R CLEAR A ! " A ! " J J
D # % D # % G & ' G & ' P P , Y Y V V : ; S S . [ = ] [ = ] { { ? } }
Using the remote control unit
Approx. 8 meters
NOTES:
• The remote control unit may not operate if the remote
sensor is exposed to direct sunlight or strong artificial
light, or if there is an obstacle between it and the remote
sensor.
• Do not press buttons on the main unit and on the remote
control unit at the same time. Doing so will result in
malfunction.
Inserting the batteries