Desa BHDV41N/P - Manual (Page 27)

27 105540
OWNER’S MANUAL
1. After lighting, let pilot flame burn for
about one minute. Turn gas control
knob on the control valve to ON posi-
tion. Turn variable control knob any-
where between HI and LO. Slide the
selector switch to the REMOTE posi-
tion.
Note: The burners may light if
hand-held remote ON button was on
when selector switch was last turned
off. You can now turn the burners on
and off with either optional hand-held
remote control unit.
IMPORTANT: Do not leave the se-
lector switch in the REMOTE posi-
tion when the pilot is not lit. This will
drain the battery.
IMPORTANT: Be sure to press the
ON/OFF buttons on the hand-held
remote control unit for up to 3 sec-
onds to assure proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the
burners on and off. When turning
burners off, the pilot will remain lit.
GHRCT Series Operation:
2. Select the MAN (manual) or AUTO
button on the hand-held remote con-
trol unit (see Figure 59).
• In manual mode, turn burners on
or off by pressing the ON or OFF
buttons on the hand-held remote
control unit.
• In auto mode, the room tempera-
ture is controlled by the thermo-
stat in the hand-held remote con-
trol unit. To increase the room tem-
perature, press the top arrow of the
TEMP button. To lower the room
temperature, press the bottom ar-
row of the TEMP button. At higher
settings the heater will run more.
IMPORTANT: This remote control
has been specially engineered to take
an air temperature sample every 5.5
minutes in auto mode. It will not re-
spond immediately to the tempera-
ture setting being turned up or down.
OPERATING
FIREPLACE
Continued
Figure 59 - Hand-Held Thermostat Remote Control Unit Selections
(GHRCT Only)
O FF
PIL OT
O N L
O IH
ON OFF REMO
TE
ON
OFF
OPERATING
OPTIONAL BLOWER
ACCESSORY
Locate the blower controls by opening
the lower louver panel on the fireplace.
Blower controls are located on the left
side of the switch bracket to the left just
inside the louver panel.
Both the GA3700 manual blower and the
DA3610T thermostatically-controlled
blower have an ON setting and an OFF
setting. The blower will only run when the
switch is in the ON position. In the OFF
position, the blower will not operate.
Note for DA3610T Only: If you are
using DA3610T blower with optional ther-
mostat (wall mount or remote control)
for the fireplace, your fireplace and
blower will not turn on and off at the
same time. The fireplace may run for
several minutes before the blower turns
on. After the heater modulates to the pilot
position, the blower will continue to run.
The blower will shut off after the firebox
temperature decreases.
The blower helps distribute heated air
from the fireplace. Periodically check the
louvers of the firebox and remove any
dust, dirt, or other obstructions that will
hinder the flow of air.
Figure 58 - Setting the Selector Switch, Gas
Control Knob, and Variable Control Knob
for Remote Operation
Selector Switch in
Remote Position
(Optional Remote
Control)
Gas Control
Knob in On
Position
Variable
Control Knob
Blower Control Knob
(Optional Accessory)
Continued
IMPORTANT: The hand-held remote
control unit must be near the heater
but not extremely close to it. The
thermostat on the hand-held remote
control unit will heat up too quickly
and turn the heater off.
3. Use the STATUS button on the hand-
held remote control unit to see the
operation mode being used and the
temperature setting selected. A red
light will come on beside the opera-
tion mode being used.
4. To turn the burners off when operat-
ing in the manual mode, press the OFF
button. If operating in the auto mode,
press the MAN button, then press the
OFF button. The pilot will remain lit.
IMPORTANT: To turn the pilot off,
manually turn the gas control knob on
the heater to the OFF position.
TEMP
STATUS
HI
LO MAN ON
AUTO OFF
Increases Room
Temperature
Decreases Room
Temperature
Turns Burners On
and Off
Shows Current
Operation Mode
Shows Temperature
Setting
Allows Burners to be
Turned On and Off with
the Hand-Held Remote
Unit.
The Heater will Auto-
matically Cycle between
Pilot and the Heat
Setting that has been
Selected.