Comtech EF Data SMS-7000 - Manual (Page 123)

SMS-7000 Modem Protection Switch Remote Control Operation
Rev. 3 Draft A–7
Backup
Multiplexer
Unit Address Command:
Response:
Status:
Response:
<add/MUA_Bx_yyy'cr'
>add/MUA_Bx_yyy'cr''lf']
<add/MUA_Bx'cr'
>add/MUA_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup multiplexer number).
yyy = 0 to 255 (backup multiplexer address; 0 places
backup multiplexer out of service).
A.3.2 Prime Modem
Prime
Modem
Address Command:
Response:
Status:
Response:
<add/ADD_x_yyy'cr'
>add/ADD_x_yyy'cr''lf']
<add/ADD_n_'cr'
>add/ADD_n_yyy'cr''lf']
Where:
x = 1 to 8 (prime modem number).
yyy = 0 to 255 (prime modem address; 0 places prime
modem out of service).
Prime
Modulator
Active
(Enable) Command:
Response:
Status:
Response:
<add/MA_x_yyy'cr'
>add/MA_x_yyy'cr''lf']
<add/MA_x'cr'
>add/MA_x_yyy'cr''lf']
Where:
x = 1 to 8 (prime modem modulator number).
yyy = YES or NO.
Note: Enter command in Manual mode only.
Prime
Demodulato
r Active
(Enable) Command:
Response:
Status:
Response:
<add/DA_x_yyy'cr'
>add/DA_x_yyy'cr''lf']
<add/DA_x'cr'
>add/DA_x_yyy'cr''lf']
Where:
x = 1 to 8 (prime modem demodulator number).
yyy = YES or NO.
Note: Enter command in Manual mode only.
Prime
Modulator
Priority Command:
Response:
Status:
Response:
<add/MP_x_y'cr'
>add/MP_x_y'cr''lf']
<add/MP_x'cr'
>add/MP_x_y'cr''lf']
Where:
x = 1 to 8 (prime modem modulator number).
y = 1 (HIGH), 2 (MEDIUM), or 3 (LOW).
Note: Independent switching mode.
Prime
Demodulato
r Priority Command:
Response:
Status:
Response:
<add/DP_x_y'cr'
>add/DP_x_y'cr''lf']
<add/DP_x'cr'
>add/DP_x_y'cr''lf']
Where:
x = 1 to 8 (prime modem demodulator number).
y = 1 (HIGH), 2 (MEDIUM), or 3 (LOW).
Note: Independent switching mode.
Prime
Modem
Priority Command:
Response:
Status:
Response:
<add/MP_x_y'cr'
>add/MP_x_y'cr''lf']
<add/MP_x'cr'
>add/MP_x_y'cr''lf']
Where:
x = 1 to 8 (prime modem number).
y = 1 (HIGH), 2 (MEDIUM), or 3 (LOW).
Note: Dependent switching mode.
Prime
Modulator
On-line
Delay Command:
Response:
Status:
Response:
<add/MD_x_yyy.y'cr'
>add/MD_x_yyy.y'cr''lf']
<add/MD_x'cr'
>add/MD_x_yyy.y'cr''lf']
Where:
x = 1 to 8 (prime modem modulator number).
NONE, or MANUAL.
yyy.y = 0.5 to 127.0 seconds (in 0.5 second increments).
Notes:
1. If MANUAL is selected, enter the number of seconds for
the delay.
2. Independent switching mode.