Document Outline

• XSAT7080X-Band Transceiver
• Errata A
• Customer Support
• Table of Contents
  • About this Manual
    • Conventions and References
      • Cautions and Warnings
      • Metric Conversion
      • Trademarks
    • Reporting Comments or Suggestions Concerning this Manual
    • Safety Notice
  • Installation Guidelines Regarding Power Line Quality
    • Warranty Policy
    • Limitations of Warranty
    • Exclusive Remedies
    • Disclaimer
• 1. INTRODUCTION
  • Introduction
• 2. SPECIFICATIONS
  • 2.1Specifications
  • Dimension Envelope
• 3. SYSTEM OPERATION
  • Pin-outs
    • Connector J3:AC Power, Mains, 100 to 125 VAC, or 205 to 240 VAC.
    • Connector J5:COMM, Remote communications port.
  • Turning On the XSAT
  • Configuring the XSAT
    • Frequency
    • Attenuation
    • Gain Offset
    • Mute Mode
    • Mute
    • Tx Amplifier
    • Channel Slope Adjust Mode
    • Channel Slope Adjust
    • Reference Frequency Adjust
    • External Reference Fault Logic
    • Cold Start Function
    • Auto Fault Recovery
    • LNA Current Source
    • LNA Current Calibration and Current Window
    • LNA Fault Logic
    • Redundancy Controller Auto/Manual
    • Redundancy Controller Toggle
    • Set Physical Address
    • Set Baud Rate
    • Set Date
    • Set Time
• 4. REMOTE CONTROL
  • Introduction
    • RS-485
    • RS-232
  • Basic Protocol
    • Packet Structure
      • Start Of Packet
      • Address
      • Instruction Code
      • Instruction Code Qualifier
      • Message Arguments
      • End Of Packet
  • Commands or Responses
• 5. REDUNDANT SYSTEM
  • Redundant System
  • RSU-5060 Interfaces
    • Electrical Interface
      • XSAT Unit A Interface, J1
      • Rx Waveguide Switch interface, J2
      • XSAT Unit B Interface, J3
      • Tx Waveguide Switch interface, J4
      • M&C Interface, J5
      • Tx IF Interfaces, J6, J7, and J8
      • Rx IF Interfaces, J9 – J11
    • Mechanical Interface
  • RSU-5060 Operation
    • RS-485 Interface
    • RED AUTO/MANUAL signal
    • SWITCH CMD signal
    • REDUNDANCY A/B signals
    • REDUND_FLT signal
    • AUXCOM signals
  • Configuring A Redundant System
• 6. THEORY OF OPERATION
  • RF Signal Conversion
    • Downconverter
    • Upconverter
  • Monitor & Control
• 7. MAINTENANCE AND TROUBLESHOOTING
  • Maintenance Testing
  • Troubleshooting
  • Converter Faults
    • DC Power Supply Voltages
    • RF Converter Module
    • Reference Oscillator Module
    • LNA Current Fault
    • Fan Fault
    • Temperature Fault
  • Equipment Return and Repair Procedure
  • Product Application, Upgrading or Training Information
• 8. XSAT-7080 +10 dBm UNIT
  • Overview
    • Function Description
    • Prime Power Level
    • Physical Dimensions
  • Specifications
• 9. EXTERNAL AMPLIFIER COMMUNICATION
  • Overview
  • External Amplifier Communication
• A. 5 - 25 WATT INSTALLATION
  • Unpacking and Inspection
  • Personnel
  • Tools Required
  • Single-Thread Configuration
    • Mounting Kit
    • Single-Thread Installation
    • LNA Installation
    • Cable Installation
  • Redundancy Configuration
    • Mounting Kit
    • Assemble TX/Remote Switch, AS/0503
    • Connect Cabling to the Remote Switch Box, AS/0490 using AS/0440 Cable Kit
    • Redundancy Installation
    • LNA Installation
    • Cable Installation
  • Spar Mounting Instruction
    • Spar Mounting kit
    • Mounting Kits
    • Mounting Instructions
• B. 50 and 100-WATT INSTALLATION
  • Unpacking and Inspection
  • Personnel
  • Tools Required
  • Single -Thread Configuration
    • Mounting Kits
    • Single-Thread Installation
    • LNA Installation
  • Cable Installation
  • Redudancy Configuration
    • Mounting Kit
    • Redundancy Installation
      • Assemble Waveguide Switch, AS/9759-1
      • Assemble Redundant Configuration
      • Assemble LNA Switch Kit, AS/9751-1
  • LNA Assembly
  • Cable Installation
• Backcover