Document Outline

• mn-kpa_r1.pdf
  • INSIDE COVER
  • Table of Contents
  • Tables
  • Figures
  • PREFACE
    • About this Manual
      • Disclaimer
      • Reporting Comments or Suggestions Concerning this Manual
    • Military Standards
    • Conventions and References
      • Metric Conversion
      • Recommended Standard Designations
      • Trademarks
    • Cautions and Warnings
    • Electrical Safety and Compliance
    • Electromagnetic Compatibility (EMC) Compliance
    • European Low Voltage Directive (LVD)
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Customer Support
      • Online Customer Support
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 KPA Specifications
      • 1.3.1 KPA-020IN Specifications
      • 1.3.2 KPA-040 Specifications
      • 1.3.3 KPA-080 Specifications
      • 1.3.4 KPA-100 Specifications
      • 1.3.5 Dimensional Envelopes
  • Chapter 2. INSTALLATION
    • 2.1 Unpacking and Inspection
    • 2.2 Rack Mounting the KPA
      • 2.2.1 Installation of the Optional Rack Slides
  • Chapter 3. CONNECTORS and PINOUTS
    • 3.1 Connector Overview
    • 3.2 RF Connections
      • 3.2.1 J1 RF IN / Tx IN Connectors
      • 3.2.2 J2 RF OUT Connector
    • 3.3 Utility Connections
      • 3.3.1 Sample Port Connectors (Front Panel)
      • 3.3.2 J4 REDUNDANT LOOP Connector
      • 3.3.3 J5 DISCRETE CONTROL Connector
      • 3.3.4 J8 10/100 ETHERNET Connector
      • 3.3.5 J9A EXT REF IN / J9B EXT REF OUT Connectors
      • 3.3.6 J7 RF SWITCH Connector
      • 3.3.7 J6 COM 1 Connector
    • 3.4 Power / Ground Connections
      • 3.4.1 Alternating Current Prime Power Switch and Connector
      • 3.4.2 Chassis Ground Connector
  • Chapter 4. FLASH UPGRADING
    • 4.1 Flash Upgrading via Internet
    • 4.2 Ethernet FTP Upload Procedure
  • Chapter 5. FRONT PANEL OPERATION
    • 5.1 Introduction
      • 5.1.1 Startup Checklist
      • 5.1.2 LED Indicators
      • 5.1.3 Keypad
      • 5.1.4 Front Panel Display
    • 5.2 Opening Screen
    • 5.3 SELECT: (Main) Menu
      • 5.3.1 SELECT: Config (Configuration)
        • 5.3.1.1 CONFIG: Remote (Remote Control)
        • 5.3.1.2 CONFIG: Amp
        • 5.3.1.3 CONFIG: FltRec (Fault Recovery) Menu Branches
        • 5.3.1.4 CONFIG: Redundancy Menu Branches
        • 5.3.1.5 CONFIG: ExtRef (External Reference)
      • 5.3.2 SELECT: Monitor
        • 5.3.2.1 MONITOR: Faults
        • 5.3.2.2 MONITOR: Stored
        • 5.3.2.3 MONITOR: Power
        • 5.3.2.4 MONITOR: Vltgs
        • 5.3.2.5 MONITOR: PS (Power Supply)
        • 5.3.2.6 MONITOR: Temp
        • 5.3.2.7 MONITOR: FETs
      • 5.3.3 SELECT: Utility
        • 5.3.3.1 UTILITY: Date/Time
        • 5.3.3.2 UTILITY: CID (Circuit ID)
        • 5.3.3.3 UTILITY: PowerMon
        • 5.3.3.4 UTILITY: Firmware
        • 5.3.3.5 UTILITY: RefOsc
      • 5.3.4 SELECT: Front Panel
        • 5.3.4.1 Front Panel: Brightness
        • 5.3.4.2 Front Panel: Lamp Test
  • Chapter 6. KPA ETHERNET MANAGEMENT
    • 6.1 Overview
    • 6.2 Ethernet Management Interface Protocols
    • 6.3 SNMP Interface
      • 6.3.1 Management Information Base (MIB) Files
      • 6.3.2 SNMP Community Strings
    • 6.4 Telnet Interface
    • 6.5 Web Server (HTTP) Interface
      • 6.5.1 Web Server page Introduction
      • 6.5.2 Web Server Interface Access
      • 6.5.3 Web Server Menu Tree
      • 6.5.4 Web Server page Descriptions
        • 6.5.4.1 Home pages
          • 6.5.4.1.1 Home (Splash) page
          • 6.5.4.1.2 Home | Support page
        • 6.5.4.2 Admin pages
          • 6.5.4.2.1 Admin | Access page
          • 6.5.4.2.2 Admin | SNMP page
        • 6.5.4.3 Config (Configuration) pages
          • 6.5.4.3.1 Config | Amplifier page
          • 6.5.4.3.2 Config | Utility page
          • 6.5.4.3.3 Config | Redundancy page
        • 6.5.4.4 Status pages
          • 6.5.4.4.1 Status | Events page
          • 6.5.4.4.2 Status | Status page
          • 6.5.4.4.3 Status | FETs page
  • Appendix A. MAINTENANCE and TROUBLESHOOTING
    • A.1 Introduction
    • A.2 Maintenance Testing
      • A.2.1 Test Point Samples
    • A.3 Troubleshooting
      • A.3.1 Troubleshooting Guide
  • Appendix B. KPA REDUNDANT OPERATIONS
    • B.1 Introduction
    • B.2 Redundancy Operation
    • B.3 Redundancy Kit Installation
      • B.3.1 Redundancy Kit Control Cabling
    • B.4 Gain Equalization of Redundant Units
      • B.4.1 Case Examples
  • Appendix C. REMOTE CONTROL
    • C.1 Overview
    • C.2 EIA-485
    • C.3 EIA-232
    • C.4 Basic Protocol
    • C.5 Packet Structure
      • C.5.1 Start of Packet
      • C.5.2 Target Address
      • C.5.3 Address Delimiter
      • C.5.4 Instruction Code
      • C.5.5 Instruction Code Qualifier
        • C.5.5.1 Backward Compatibility Code Qualifier
      • C.5.6 Optional Message Arguments
      • C.5.7 End of Packet
    • C.6 Remote Control Using FW Version 2.X.X and Higher (CURRENT)
      • C.6.1 Remote Commands and Queries (FW Version 2.X.X and Higher)
    • C.7 Remote Control Using Firmware Version 1.X.X (OLD)
      • C.7.1 Old Utility Commands
      • C.7.2 Old Configuration Commands
      • C.7.3 Old Operating Mode Commands
      • C.7.4 Old Status Commands
      • C.7.5 Old Stored Alarms
      • C.7.6 Error Processing
      • C.7.7 Configuration Errors
      • C.7.8 Time-Outs
  • METRIC CONVERSIONS
• BACK COVER