Grip Factory Munich GF-Primo - Manual (Page 3)

GF-Primo / GF-Secondo Dolly System Instruction Manual
Page: 2
SAFETY GUIDELINES
Adherence to the instruction manual:
The set-up instructions must be read and understood before set-up or operation. The dolly may only be
assembled in accordance with the manufacturer’s instruction manual. The manufacturer’s technical
specifications and limits (maximum rated loads etc) must be adhered to at all times and in no way exceeded.
Warranty:
The manufacturer accepts no liability for damages or injuries for incidents or accidents occurring due to
negligence by the crane operator or misuse of the crane or disregarding the instruction manual.
Assembling and operation of the dolly:
The Dolly may only be set-up or operated by trained and experienced personnel. To assemble and operate
the dolly at least 1 trained person is required. To avoid misuse by untrained personnel, the dolly should be
dismantled / switched off when not in use or under supervision.
The crane may not be set-up or operated under the influence of alcohol, drugs or any other intoxicating
substances. The respective protective clothing e.g. gloves, should be worn.
Stability of the crane system:
Before assembling or using the dolly ensure that the ground surface is stable and cannot give way. The
ground surface must be stable enough to support at least 1000 kg/m2 = 2200 lbs/ sq yard.
Dolly operation with the GF-Primo Jib is only allowed with solid tires and use with pneumatic wheels is not
allowed. Before and while using the dolly wheels should be inspected.
Intended use of the Dolly system and use of the Dolly system with Jib Arm:
The Dolly is a mobile personnel and camera support system for use on sets and studios with even and level
ground / floors. Also for use on GF-Track.
Standard dolly operation consists of a for lifting 1 to 2 persons and camera or lifting the camera only, without
personnel on board, electromechanical column for lifting 1 to 2 persons and camera or lifting the camera
only, without personnel on board.
In Jib mode a pan and tilt arm is mounted for lifting 1 to 2 persons and camera or lifting the camera only,
without personnel on board
In accordance to the safety guidelines the dolly/jib is only allowed to be used on solid, level and stable
ground with solid wheels, not pneumatic wheels.
The dolly/jib movement on the ground, rotation of the column is managed by at 1 to 2 experienced, trained
and authorised personnel from the hand grips and /or the provided steering handles.
Panning movement of the turnstile mount / column can also be made by the personnel sitting on the
column/dolly when seated on the provided seats.
Vertical lift of the column is controlled via wireless or cable control operated by an experienced, trained and
authorised person.
Operation of the dolly/jib is only allowed within the limits and guidelines mentioned in this instruction manual.
The dolly must be operated on level, stable surfaces at all times or on dolly track. Whether operating or
moving the dolly on track or on a solid ground surface it is essential that the track or surface is completely
level, stable and free from obstructions.
When operating the dolly on track, ensure that the track is level, properly laid, constructed and supported.
The correct underlay must be used to ensure that the track and underlay are secured against moving,
slipping and collapse. Ensure that the underlay meets the specified support and stability requirements. Only
GFM Track or comparable track systems with a payload capacity of 1200kg / 2640lbs and a maximum track
runner distance of 640mm / 25inches (measured inside edge to inside edge) may be used.
Extreme caution if tracking on curved track (not faster than a slow walking pace)!
Use of the dolly on insert vehicles, camera cars or any motorised vehicle is not allowed. The
manufacturer accepts no liability for damages or injuries for incidents or accidents occurring due to use of
the dolly on insert vehicles, camera cars or any other motorised vehicles.
Operation of the Dolly/ Jib:
The complete lift and panning range of the dolly/jib must be kept clear of obstructions at all times. A safety
clearance of 1m / 3' 3" must be observed on all sides of the dolly/jib during operation. Only authorised,
trained and experienced personnel are allowed to operate the dolly/jib. The dolly/jib may not be set-up or
operated under the influence of alcohol, drugs or any other intoxicating substances. The respective
protective clothing e.g. gloves, should be worn.
The dolly may not be used in the direct vicinity of high voltage power cables. To avoid accidents due to
misuse in the vicinity of high voltage power cables, Safety Guidelines especially BGV A1 and A2 (formerly