Denon DN-HD2500 - Manual (Page 16)

ENGLISH
11
• Each push of the PLAY/PAUSE button
switches between playback and
pause. PLAY/PAUSE button
illuminates solid green during
playback and flashes in pause.
• When the PLAY/PAUSE button is pushed during play,
the DN-HD2500 pauses playback at that point. Push
PLAY/PAUSE button once again and playback resumes.
• Playback will pause when SCRATCH
is selected with the JOG MODE
button and the JOG disc is held with
your hand. Playback resumes when
your hand is released.
5 BASIC OPERATION
Play and pause
1
2
Push the PITCH/KEY button to
PITCH indicator lights up.
• PITCH → KEY (key adjust) →
OFF
NOTE:
The display will indicate “KEY”, when key adjust is
ON.
Move the Pitch Slider to adjust the
pitch. The current pitch setting is
displayed on the display.
Pitch decreases
Pitch increases
• When the CUE button is pushed
during playback, the file stops and
returns to the original position of
which playback started from, the (Cue
point). This function is also called
Back-Cue. With the Back-Cue function, you can start
from exactly same position. The CUE button illuminates
solid red when DN-HD2500 is ready to start playback.
• You can set and change Cue point as follows.
• When you started playback.
• File select finished.
• Manual search.
Play and Cue
• If you would like to start playback other from the
beginning of the file, you need to move Cue Point using
fast Search, scan and manual search function.
• With Pitch slider you can adjust the playback speed
(Pitch).
• If you would not prefer to change key of sound, use the
Key Adjust function.
Adjusting the pitch
3
DN-HD2500 has six pitch ranges,
4 %, 10 %, 16 %, 24 %, 50 %
and 100%. When the RANGE
button is pushed for more than 1
sec, the pitch range can be
selected with the
PARAMETERS knob.
• When the PARAMETERS
knob is pushed the pitch
range is entered and the
pitch range selection mode is cancelled.
• With PITCH BEND function you can change pitch
temporary. DN-HD2500 has two ways for this function
PITCH BEND buttons and JOG disc.
Pitch Bend
1
[PITCH BEND +/– buttons]
• Push the PITCH BEND
button for momentary
change of pitch.
While holding these buttons
down, the pitch continues to change up to the
limitation.
• After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
• Turn the PARAMETERS knob or
JOG disc.
Select the file
! Move the Cue point
Power on play
• When “POWER ON PLAY” is set to “ON” at ⁄5
PRESET “(10) Power On Play”, playback starts from
the first file on the “Favorites” when the power is
turned on.
2
[JOG disc]
• When the JOG mode is set to
SEARCH/BEND with the JOG
MODE button, the playback
speed can be changed by turning
JOG disc during playback.
4
After you found your preferred
Cue point, push the CUE button
then a new Cue point is set.
2
Push the JOG MODE button to
set JOG disc to search mode.
The JOG MODE button will
turn off.
3
Turn the JOG disc to change Cue
point. You can hear the short
sound of the current Cue point.
When JOG disc is turned in the
pause, Cue or frame repeat mode,
it works as the manual search function.
1
You can move to the
approximate playback start
position by FAST SEARCH
buttons.
[QUICK JUMP]
• If the FAST SEARCH button is tapped shortly,
the playback position jumps about 10 seconds.
The jump time can be selected in the preset
mode from 10, 20, 30 or 60 sec.
[FAST SEARCH]
• When the FAST SEARCH button is pressed
and held in, the file/Track is fast-searched.
ENGLISH