Denon AVR-3310CI - Manual (Page 14)


Connections
Set
tin
g
s
Inf
or
mation
Specifications
Get
ting Star
te
d
Una
vailable F
unctions
Af
ter Upgr
ading
ENGLISH
Setting items Setting contents
Surround Parameters
(Continued)
This can also be set by pressing STANDARD.
If the source being played contains a surround back signal, the decoder
type is automatically selected by the AFDM function. Set “AFDM” to
“OFF” to switch to your preferred decoder.
If the setting in “Speaker Configuration” – “Surround Back” (vpage 9)
is “None”, “Surround Back” is not displayed. •
•
•
Subwoofer Att. : Attenuate subwoofer level when using EXT. IN input.
ON : Set.
OFF : Do not set.
Usually use in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
•
•
Subwoofer : Turn subwoofer output on and off.
ON : The subwoofer is used.
OFF : The subwoofer is not used. •
•
Default : Restores all the surround parameter settings to their defaults.
No : Do not reset to the defaults.
Yes : Reset to the defaults. •
•
Tone
Adjust the tonal quality of
the sound.
Tone Control : Sets the tone control function ON and OFF.
ON : Allow tone adjustment (treble, bass).
OFF : Playback without tone adjustment.
This can be set when “Dynamic EQ” (vpage 14) is set to “OFF”.
The tone cannot be adjusted in the direct mode.
•
•
•
•
Bass : Adjust low frequency range (bass).
–6dB ~ +6dB
This can be set when “Tone Control” (vpage 13) is set to “ON”.
•
Treble : Adjust high frequency range (treble).
–6dB ~ +6dB
This can be set when “Tone Control” (vpage 13) is set to “ON”.
•
Setting items Setting contents
Audyssey Settings
Set Audyssey MultEQ®,
Audyssey Dynamic EQ®
and Audyssey Dynamic
Volume™.
NOTE
If you have not performed
Auto Setup, or if you
change the speaker
settings after performing
Auto Setup, you may not
be able to select Dynamic
EQ/Dynamic Volume, and
“Run Audyssey” may be
displayed.
In this case, either perform
Audyssey Auto Setup over
again or perform “Restore”
(vpage 33 of GThe
original versionH Operating
Instructions) to return to
the settings after Audyssey
Auto Setup was run.
MultEQ : Corrects both time and frequency response problems in the
listening area.
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual : Apply frequency response set with “Manual EQ” (vpage
16).
OFF : Turn “MultEQ” equalizer off.
“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after Audyssey Auto Setup has been performed. “Audyssey”
is automatically selected after performing Audyssey Auto Setup. “When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, “
”
lights.
After running Audyssey Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “
” lights.
If “Dynamic EQ” or “Dynamic Volume” is set to “ON” when “MultEQ”
is set to either “OFF” or “Manual”, “MultEQ” is automatically set to
“Audyssey”.
You can also press
MULTEQ to set.
NOTE
“MultEQ” and “Manual EQ” cannot be selected when “EQ Customize”
is set to “Not Used” (vpage 38 of GThe original versionH Operating
Instructions).
When using headphones, “MultEQ” is set to “OFF”.
•
•
•
•
•
•
•
•
•
•
•
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Pla
ybac
k
Main remote control
operation buttons
:Displaying the menu
Cancel the menu :Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu