Orion System OE338-23-XX - Manual (Page 5)

Form: ORION-OE331-21-KWH-Module-01A.doc
Page 1 of 1
Description
The OE331-21-KWH (Kilowatt Hour)
Module provides the ability to record and
display KW usage and to limit demand
on your control system. Using the Prism
Graphical Computer Front End, a status
screen displays current demand, yester-
day’s demand, and the peak demand
values and times for both. Historical logs
from the previous month and the current
month are also available and can be
downloaded for archiving via the PRISM
software interface. A running total of
power consumption is also displayed on
the status screen. This value can be
manually reset at any time allowing the
user to monitor overall power consump-
tion over long periods of time.
Analog Input #2 on the KWH Module
monitors all incoming contact closures
from a KW pulse meter (usually provided
by the utility company) and times them to
generate the current KW Demand. A
user adjustable setpoint is provided to
define what each pulse represents in
Kilowatts Per Hour. A Demand Factoring
Constant is also provided if it appears that contact bounce may be affecting the operation. The Demand Factor is
simply the number of times to average the current demand reading to create the final Demand Reading. It is nor-
mally left at a value of '1' unless a problem is encountered.
Two additional setpoints are provided for the EMS Demand Limiting Broadcast. A Limit Setpoint and a Propor-
tional Reset Range are provided so that the user can adjust when to begin shedding demand and how rapidly
this occurs. Any controllers equipped to "hear" this broadcast begin spreading their heating and cooling setpoints
proportionally until the maximum EMS Adjustment limit is reached. This value is also user adjustable for each
individual controller so that the rate at which demand is shed can be optimally configured for special cases where
not all zones can tolerate a large change in temperature.
Mounting
The KWH Module is provided with an integral backplate for mounting inside of a control enclosure. It is recom-
mended that the KWH Module be mounted in a control enclosure in the building equipment room. An optional
factory control enclosure for the KWH Module is available.
OE331-21-KWH
KWH Module
Technical Data OE331-21-KWH
KWH Module
Power 24 Volt AC Weight 1.5 lb.
Power Consumption 8 VA Maximum Network Connection RS-485
Operating Temp 10 °F to 149°F Protocol HSI Open Protocol Token Passing
Operating Humidity 90% RH Non-Condensing Communications RS-485 - 9600 Baud
Input Output
Location Type Location Type
AIN2 Dry Contact Closure KW
Pulse Meter (By Others)
RS-485 Communications Loop EMS Demand Limiting
Broadcast
Three Year Warranty WattMaster reserves the right to change specifications without notice
RL Y 1
D1
D2
D3
D4
D5
CX
3
RAM EPROM
C3
C2
U6
PH
IL IP S
CX6
C1
CX2 U2
U3
PAL
CX4
U4
TUC-5R PLUS
YS101816 REV. 2
V1
V2
V3
V5
V4
TB2
4
NETWORK
TOKEN
16
32
8
SW1
ADD
2
1
ADDRESS
V6 PO
W E R
GND
24VAC
L1
D1 6
R6
C9
SC1
R1 1
U1 1
MC 34064 A
D1
3
C16
9936
VR2
7824C T
M
TB4
R27
C13
R1 0
VR1
C1 9 C1 8
NE5090NPB3192 0PS
U8
CX
8
U9
X1
R7 D1 0
R13 D12
C7 CX10
U10
CX12
U12
U14
CX14
PJ3 PJ2
PJ1
EXPANSION
PRESSURE
SENSOR
T'STAT
C17 D15
R26
C20 R25
R24
R22
U15
CX13
U13
C15
R19
R15
C14
D1 8 D1 7
PU1
PU2
PU3
PU4
PU5
PU7
D6
D7
D8
D9
D11
D14
C12
C10 0- 5
VD
C 0- 1
VD
C
JP1
C1 1
X2
GND
TB3
INPUTS
GND
GND
+VDC
AIN1
AIN2
AIN3
AIN4
AIN5
AOUT1
AOUT2
AIN7
RN
4
1
RN5
RS-485
CX5
U5
R
TB1
SHLD
T
COMM
COMM
RN
3
1
RN1
U1
CX1
1
LD6
COMM
PWR LD7
LED1
LED2 LD9
LD8
R1
U7
RV1
VREF ADJ
R28
+VREF
5.11V
TEST POINT
EWDOG
D19
RN2
1
COM1-3
COM4-5
R5
R4
R3
R2
R1
RL
Y 2
RL Y 3
RL Y 4
RL
Y 5
CX15
(1 MEG) HH
P1
C2
1
6.2“
6.6”
7.3”
6.7”
1.1”
.20 Dia.
Typ. of 4