Teac US-16X08 - Manual (Page 15)

TASCAM US-16x08
15
Line inputs (unbalanced) LINE IN11-16
(LEVEL switch set to “−10 dBV”)
Connectors:
6.3 mm (1/4") standard TS stereo
jacks
(Tip: HOT, Sleeve: GND)
Input impedance:
10 kΩ
Rated input level: −10 dBV (0.3162 Vrms)
Maximum input level: +10 dBV (3.162 Vrms)
Line inputs (balanced) LINE IN11-16
(LEVEL switch set to “+4 dBu”)
Connectors:
6.3 mm (1/4") standard TRS stereo
jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Input impedance:
10 kΩ
Rated input level: +4 dBu (1.228 Vrms)
Maximum input level: +24 dBu (12.282 Vrms)
Analog outputs
Line outputs (balanced) LINE OUT1-8
Connectors: 6.3 mm (1/4") standard TS stereo
jacks (Tip: HOT, Sleeve: GND)
Output impedance: 100 Ω
Rated output level: +4 dBu (1.228 Vrms)
Maximum output level: +24 dBu (12.277 Vrms)
Headphones output (PHONES)
Connector: 6.3 mm (1/4") standard stereo jack
Maximum output: 70 mW + 70 mW
(THD+N 0.1 % or less, into 32 Ω load)
Frequency response
Input to PHONES
44.1kHz, 48kHz
20Hz to 20kHz:
±1.0 dB(JEITA) Hi-Res compatible
88.2kHz, 96kHz
20Hz to 40kHz:
±2.0 dB(JEITA) Hi-Res compatible
Control input/output ratings
MIDI IN connector
Connector: 5-pin DIN
Format: standard MIDI
MIDI OUT connector
Connector: 5-pin DIN
Format: standard MIDI
USB
Connector: 4-pin USB B-type
Transfer rate: USB 2.0 High Speed (480 Mbps)
Audio performance
Mic preamp EIN (equivalent input noise)
−125 dBu or less
Frequency response
Inputs to LINE OUT (BALANCED)
44.1 kHz, 48 kHz
20 Hz to 20 kHz:
±0.5 dB (JEITA)
88.2 kHz, 96 kHz
20 Hz to 40 kHz:
±0.5 dB (JEITA)
S/N ratio
100 dB or more
(MIC/LINE IN to LINE OUT, gain knob at MIN, JEITA)
Distortion
0.006 % or less
(MIC/LINE IN to LINE OUT, 1 kHz sine wave, rated maximum
input level, maximum output level)
Crosstalk
100 dB or higher
(MIC/LINE IN to LINE OUT, 1 kHz)
Computer system requirements
Check the TEAC Global Site (http://teac-global.com/) for the
latest information about supported operating systems.
Windows
Supported operating systems
Windows 8 (including 8.1) 32-bit
Windows 8 (including 8.1) 64-bit
Windows 7 32-bit SP1 or later
Windows 7 64-bit SP1 or later
(Windows Vista and Windows XP are not supported)
Computer hardware requirements
Windows computer with a USB 2.0 port
CPU/processor speed
2 GHz or faster dual core processor (x86)
Memory
2 GB or more
CAUTION
Operation of this unit was confirmed using standard
computers that meet the above requirements. This does
not guarantee operation with all computers that meet the
above requirements. Even computers that meet the same
system requirements might have processing capabilities
that differ according to their settings and other operating
conditions.