Document Outline

• Front Matter
  • Copyright Notice
  • Trademarks
  • FCC Requirements
  • Canadian Emissions Requirements
  • Warranty
  • Customer Service
  • Returning Products
  • Safety Precautions
    • About This Manual 1
    • Chapter 1, General 3
    • Chapter 2, Installation 11
    • Chapter 3, General Operation and Conventions 17
    • Chapter 4, Operation 21
    • , Affidavit for the Connection of Customer Premises Equipment to 1.544Mbps and/or Subrate Digit...
  • Table of Contents
• About This Manual
  • What is a Reference Manual?
  • Where to go for Information
  • Conventions
• 1 General
  • Introduction
  • FrameStart Install Mode
  • FrameStart Monitor Mode (optional)
    • What is LMI Sourcing and why is it important?
    • What is a DLCI?
    • What messages does LMI provide?
    • What is PVC Discovery in FrameStart?
    • What is PVC Delay Testing?
    • What is a WAN receive level?
    • What is LMI Monitoring?
    • What is LMI Auto Sourcing?
    • What is SOS Mode?
    • What is New Circuit Install?
    • How does FrameStart work in a typical application?
      • INSTALL: LMI Mode is ON
      • MONITOR: LMI Mode is MON (Optional Feature)
      • OFF: LMI Mode is OFF
  • FrameStart Benefits
  • Ordering Numbers
  • Feature Summary
  • General Specifications
    • Management Interface
    • Alarms
    • Power Source
    • Mechanical
    • Environmental
    • Industry Listings
  • Specifications Chart
• 2 Installation
  • Introduction
  • Safety Summary
  • Unpackingand Inspection
  • Supplied Materials
  • Rear Panels
  • Data Connections
    • V.35 Data Port
    • DDS CSU/DSU Network Port
    • T1 CSU/DSU and FrameStart FSE Network Connection
      • Receive Levels
      • RJ-48C Network Connector
      • BNC Network Connectors
      • T1 NetworkDisconnection
    • Power
• 3 General Operation and Conventions
  • Introduction
    • DDS CSU/DSU Front Panel
    • LCD Access
    • Password Protection
      • To Enter an Established Password
    • Interface Conventions
      • Menu Title
      • Menu Element
      • Information Element
      • Cursor Elements
  • Hardware Reset
  • Utilities
    • Software Version
    • Restore Factory Settings
    • Set Password
• 4 Operation
  • Introduction
    • Menu Start-up Display
      • N (Network Status)
      • D (DTE Status)
      • F (Frame Relay Status)
    • Main Menu
    • Alarms
      • Reset Timer
      • Reset Alarms?
    • Performance
      • Network Performance
      • Frame Relay Performance
    • Maintenance
      • Loop
      • BERT
      • Test Patterns
      • Inject Error
      • Error Count
      • Clear Error Count
    • DDS DTE Configuration
      • Rate
      • DTE Clock
      • TXCC Clock
      • DTE Data
      • CTS
      • CTS Delay
      • DCD
      • DSR
      • DTR
    • T1 Network Configuration
      • Framing
      • Line Code
      • Clock Source
      • Sensitivity
      • LBO
      • Yellow Alarm
      • Density
      • FDL
      • Channels Assigned
      • Start Channel
      • #Channel
    • T1 DTE Configuration
      • Rate
      • DTE Clock
      • TXCC Clock
      • DTE Data
      • CTS
      • DCD
      • DSR
      • DTR
    • E1 Network Configuration
      • Framing
      • CRC4 Mode
      • E-Bit Mode
      • Clock Source
      • RAI Alarm
      • Timeslot 01 to Timeslot 31
    • E1 DTE Configuration
      • DTE Clock
      • TXCC Clock
      • DTE Data
      • CTS
      • DCD
      • DSR
      • DTR
    • Frame Relay Configuration
      • LMI Mode
      • Unit ID
      • N391
      • N392
      • N393
      • T391
      • PVC Mode
      • SOS TX (Monitor Mode)
      • SOS RX (Monitor Mode)
• Affidavit for the Connection of Customer Premises Equipment to 1.544Mbps and/or Subrate Digital...
• Warranty Statement