Verilink PRISM 3010 (CG) Configuration/Installation Guide - Manual (Page 2)

Port Configuration Menu
The Voice Card Configuration screen display allows the assignment of voice DS0s
to network channels. This display is accessible from the PRISM unit front panel
LCD, its terminal interface, or the 8100A Site Controller under the Configuration
top level menu. Only the voice ports with the Mode parameter set to ACTIVE are
connected to the selected network channel.
The 3010 voice modules have six voice circuits, each of which is independently
assignable to a selected network channel. For a more detailed description of voice
port operation, refer to the reference manual for the product where the card is
located. The following fields are available for voice port configuration:
Port: This field indicates the port number of the card in the assigned slot.
DS0: This field assigns the voice port to a network channel. The choices are
channels 1 through 24.
Mode: This field selects whether the voice port is actively assigned to a network
channel, ACTIVE, or is not used, SPARE. If set to SPARE, the other voice port
parameters are ignored and the port is inactive.
State: This field displays the voice port status as either in the BUSY or IDLE state.
Name: This field may be used to provide up to 20 characters of text for identify-
ing the voice circuit name and number.
Signalling: This field selects the supervisory operation of the voice port. The
choices for the different modules are as follows.
FXS
• FXS/LS Foreign Exchange Station / Loop Start
• FXS/GS Foreign Exchange Station / Ground Start
• MEG/LS MEGACOM ® / Loop Start
• MEG/GS MEGACOM / Ground Start
• PLAR Private Line Automatic Ringdown
• DID/DNIS Direct Inward Dialing /Dialed Number Identification
Service [Dial Pulse Originate (DPO) mode]
• DNISW/LS Loop Start DNIS (LS-DNIS) with wink
• DNISD/LS LS-DNIS with delay start
• DNISWR/LS LS-DNIS with wink and Reverse Battery
• DNISDR/LS LS-DNIS with delay and Reverse Battery
• DNISW/GS Ground Start DNIS (GS-DNIS) with wink
• DNISD/GS GS-DNIS with delay start
• DNISWR/GS GS-DNIS with wink and Reverse Battery
• DNISDR/GS GS-DNIS with delay and Reverse Battery
FXO
• FXO/LS Foreign Exchange Station / Loop Start
• FXO/GS Foreign Exchange Station / Ground Start
• FXO UVG Foreign Exchange Office/Universal Voice Grade
• FXO UVGR Foreign Exchange Office/Universal Voice Grade
with Reverse Battery
• DID/DNIS Direct Inward Dialing/Dialed Number Identification
Service [Dial Pulse Terminate (DPT) mode]
4 -Wire E&M F-3010-200--112 F-3010-200--114
• Type I Signalling YES YES
• Type II Signalling YES YES
• Type III Signalling YES YES
• Type IV and V Signalling NO YES
• TO Transmission Only YES YES
Delay Seconds: If the signalling mode has a delay, it can be set from 1 to 5 seconds.
Tx Gain: This field selects the transmit gain over the following ranges:
2 -Wire FXS: -4.0 dB fixed
2 -Wire FXO: -6 dB to 0 dB
4 -Wire E&M: -10 dB to +3 dB, 0 dB
Rx Gain: This field selects the receive gain over the following ranges:
2 -Wire FXS: -11 dB to 0 dB
2 -Wire FXO: -6 dB to 0 dB
4 -Wire E&M: -16 dB to +2 dB, 0 dB
Slot/Channel Allocation: These display -only fields indicate the network chan-
nel assignments with Channel 1 on the left and Channel 24 on the right. The upper
line indicates the card slot to which the channel is allocated. The lower line indi-
cates the port in the assigned card for that channel.
2-Wire FXS Screen
3060 DSU Time: HH:MM:SS
Element Rev xx.xx/x.xx Date: MM/DD/YY
--------------------- VOICE CARD CONFIGURATION -------------------
Slot: (2)
Card Type: 2 Wire FXS
Delay Tx Gn Rx Gn
Port DS0 Mode State Name/ID Sig. Secs. dB dB
------------------------------------------------------------------
A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2)
B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] (-4.0) ( -2)
C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] (-4.0) ( -2)
D ( 4) [SPARE ] IDLE ( ) [MEG/GS] (-4.0) ( -2)
E ( 5) [SPARE ] IDLE ( ) [PLAR ] (-4.0) ( -2)
F ( 6) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2)
222222 333333 ------ ------
Channel Allocation: ABCDEF AAAAAA ------ ------
---------------------------- Messages ----------------------------
2-Wire FXO Screen
4-Wire E&M Screen
MEGACOM is a registered trademark of AT&T.
3060 DSU Time: HH:MM:SS
Element Rev xx.xx/x.xx Date: MM/DD/YY
--------------------- VOICE CARD CONFIGURATION -------------------
Slot: (2)
Card Type: 2 Wire FXO
Delay Tx Gn Rx Gn
Port DS0 Mode State Name/ID Sig. Secs. dB dB
------------------------------------------------------------------
A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] ( -6) ( -2)
B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] ( -6) ( -2)
C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] ( -6) ( -2)
D ( 4) [SPARE ] IDLE ( ) [MEG/GS] ( -6) ( -2)
E ( 5) [SPARE ] IDLE ( ) [FXO/GS] ( -6) ( -2)
F ( 6) [ACTIVE] BUSY ( ) [FXO/LS] ( -6) ( -2)
222222 333333 ------ ------
Channel Allocation: ABCDEF AAAAAA ------ ------
---------------------------- Messages ----------------------------
3060 DSU Time: HH:MM:SS
Element Rev xx.xx/x.xx Date: MM/DD/YY
--------------------- VOICE CARD CONFIGURATION -------------------
Slot: (2)
Card Type: 4 Wire E&M
Delay Tx Gn Rx Gn
Port DS0 Mode State Name/ID Sig. Secs. dB dB
------------------------------------------------------------------
A ( 1) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2)
B ( 2) [ACTIVE] IDLE ( ) [TYPE 3] (-.5) ( +2)
C ( 3) [ACTIVE] BUSY ( ) [TYPE 2] (-.5) ( +2)
D ( 4) [SPARE ] IDLE ( ) [TO ] (-.5) ( +2)
E ( 5) [SPARE ] IDLE ( ) [TYPE 1] (-.5) ( +2)
F ( 6) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2)
222222 333333 ------ ------
Channel Allocation: ABCDEF AAAAAA ------ ------
---------------------------- Messages ----------------------------
Sales and Marketing
800 -285-2755
256 -772-3770
[email protected]
Technical Support
800 -285-2755
256 -772-3770
[email protected]
Returns /RMA
800-285-2755, ext. 2282
127 Jetplex Circle
Madison, Alabama 35758
www.verilink.com